Jump to content
SAU Community

Recommended Posts

  • Replies 199
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

looks like a top event. sorry I had to quietly opt out and didn't make it down.

Instead I stayed in nsw, got work done on friday, then brisbied my car at eastern creek on sunday :) looks like I would have been better off at deca.

looks like a top event. sorry I had to quietly opt out and didn't make it down.

Instead I stayed in nsw, got work done on friday, then brisbied my car at eastern creek on sunday :) looks like I would have been better off at deca.

Dude this sounds bad what happened????

Dude this sounds bad what happened????

basically

poor set-up rear end (was trying new set-up, but 8kg springs + 28mm sway bar = no rear end grip).

poor driver

snap oversteer

concrete wall

picture011at2.jpg

basically

poor set-up rear end (was trying new set-up, but 8kg springs + 28mm sway bar = no rear end grip).

poor driver

snap oversteer

concrete wall

picture011at2.jpg

Ouch dude.... least it wasn't tooo bad!!! Kisses u can handle hits hurt!!!

I missed this before.....

Heh thanks to the late night crew as well, was good fun!

Im not sure if Id call it a late night, or an early morning!!

But agree - was fun.

Oh yeah.... and next time, im taking your credit cards too :) - your just as bad (if not worse) than the Bris.

rest of the vids have finally finished uploading:

http://decamay07.racemeets.net/

so basically if u hit the skid pan in either of the morning sessions you should be there

cheers

thanks for the great vids. nice work

rest of the vids have finally finished uploading:

http://decamay07.racemeets.net/

so basically if u hit the skid pan in either of the morning sessions you should be there

cheers

Thanks heaps for posting the vids mate, they are great to watch. I liked the zoomed in take off shot on one of my runs :D

Cheers

Ben

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Looks great, I hope everything is working well after all that time!
×
×
  • Create New...