Jump to content
SAU Community

Recommended Posts

hey guys

changed my gearbox oil this wkend - seems to have made a nice difference especially gear changes higher up the rev range (ie: when booting it). Heres the link on my site below...

anthonymcgrath.co.uk - changing your gearbox oil

Link to comment
https://www.sau.com.au/forums/topic/169551-changing-gearbox-oil/
Share on other sites

thanks motoman I'll amend my tut to include that :O

have to say at first I did think my filler plug weren't budging but it was just the glue/sealant around the thread. I was more worried at the very very loose gearbox drain plug!!

  • 2 weeks later...

although only going to work if there is two of you. i refill my oil by using a 1.5m piece of flexible pipe with a funnel attached to one end. (i think its about 12mm in diameter.. although could be bigger...)

Run the funnel though the drivers side of the engine bay. Have one person ensure that the pipe stays pointed into the gear box filler hole while the other poors the new oil into the funnel. much easier than getting up and down lotsa times.

Cam

If you have 3 different sized ratchets in a set, you'll find the biggest one fits in perferctly without any attatchments.

Also, i bought some of the red coloured sealant/thread locker to stop the screw coming loose later.

Can't remember what it was called.

If you have 3 different sized ratchets in a set, you'll find the biggest one fits in perferctly without any attatchments.

Also, i bought some of the red coloured sealant/thread locker to stop the screw coming loose later.

Can't remember what it was called.

i believe its called lock tight ?

I think you will find that it's a 1/2 " drive ratchet that will undo the bolts. also, on r33 you can remove the gearstick suround and rubber boot and just pour it in from inside the vechile

You sure pooring it in from the gearstick surround is ok???? sounds much easier.

My gear stick surround is all torn and broken is it posible for the oil to dry up??? changing gears seems very stiff just lately and did a box oil change only 10k ago!

hopefully i'll be doing this on the weekend and i'm gonna give the filling through the gearstick option a go (i'm sooo scared of pouring oil all through my car though cos I'm so impatient when pouring oil through a funnel!)

If that for some reason doesn't work (no reason why it shouldn't off course) i'll just use a $3 syphon hand pump i reckon.

  • 1 month later...

Thanks for the writeup!

However... I tried this today and failed :D First, I dented the chassis rail with a stand. I thought the chassis rail was supposed to be tough enough to put a stand under. Where is a good place to put stands?

Then, I couldn't get the filler plug out. I had about 40cm of leverage but it just wouldn't budge.

Just to be sure... it's anticlockwise to undo, like everything else, right?

Would it be OK to use a hammer on my lever to get it started?

First, I dented the chassis rail with a stand. I thought the chassis rail was supposed to be tough enough to put a stand under. Where is a good place to put stands?

Then, I couldn't get the filler plug out. I had about 40cm of leverage but it just wouldn't budge.

Just to be sure... it's anticlockwise to undo, like everything else, right?

Hi there, have a read of this for jacking locations:

jackinglocationgu7.jpg

Also, you could try using a hammer, but I recommend getting something to extend your breaker bar/ratchet... nice length of pipe to get some more purchase, and soaking it in some WD40 will help. The filler plug is tapered so thats why it's so tight...

And just remember lefty loosey, righty tighty :laugh:

  • 11 months later...

I might try this fairly soon. I was also told, if you are tight-arsed about doing it properly, you pour a litre and abit of kerosene into the gearbox once the oil

has drained. Start the engine and push the gearstick into gear (without the clutch) so its resting on the gear but not actually going into gear. Apparently this

engages the synchros and cleans them. Once done drain the kerosene, fill it up with oil + some nulon G70 stuff and should be good :thumbsup:

Ill be doing it soonish so ill post it up on how it goes :P

I might try this fairly soon. I was also told, if you are tight-arsed about doing it properly, you pour a litre and abit of kerosene into the gearbox once the oil

has drained. Start the engine and push the gearstick into gear (without the clutch) so its resting on the gear but not actually going into gear. Apparently this

engages the synchros and cleans them. Once done drain the kerosene, fill it up with oil + some nulon G70 stuff and should be good :thumbsup:

Ill be doing it soonish so ill post it up on how it goes :P

make sure u got room infront of ur car incase u do put it in gear and it hops into wall, other car, human etc. never heard of this mate but good luck with it

Edited by skylinekid
I think you will find that it's a 1/2 " drive ratchet that will undo the bolts. also, on r33 you can remove the gearstick suround and rubber boot and just pour it in from inside the vechile

My dad says thats how he did it on the old R31 we had. It just involves pulling apart the centre console, removing the boot and pouring it in from there. Not to way to do it if you have a habbit of getting oil everywhere... like me :bunny:

I'm going to change my gearbox oil this weekend (I think) so I'll take pics if I decide to do it from inside the car :happy:

  • 6 months later...
this is probably kinda stupid to ask, does the gearbox reservoir goes to lsd reservoir as well?are they linked?or they're both independent?

The LSD is a limited slip differential. The diff or diffs (in a GTR) have there own drain and fill up point, as the oil needs to be around the diff's crown and pinion wheels for lubrication.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...