Jump to content
SAU Community

Recommended Posts

hey guys was just looking for some info on installing a front facing plenum and i found this beauty, not sure if its been posted b4 but it looks the goods.

http://www.nissanpacific.com/reference/rb/index.htm

This is what the site contains

Day 1

Cross Pipe Removal

Day 2

Thermostat Housing Removal

Intake Removal

A/C Bracket Removal

Day 3

Crank Angle Sensor Removal

Timing Chain Cover Removal

Day 4

Timing Belt Removal

Water Pump Removal

Thermostat Removal

New N1 Water Pump

Oil Pump Removal

Day 5

Water Pump Install

Oil Pump Install

Timing Belt Install

Day 6

Intake Manifold Install

Day 7

Oil Pickup Install

Oil Pan Install

Oil Cooler Bracket

Timing Belt Cover Install

Day 8

Motor Mounts

Nismo Thermostat Install

ATI Damper Install

Alternator Install

Day 9

Spark Plugs

Flywheel Install

Clutch Install

Transmission Install

Mount the motor

Day 10

Heat Shield Removal

Turbo Manifold Removal

Stock Ex. Manifold Removal

HKS Wastegate/Manifold

Day 11

Broken Stud

Day 12

HKS Wastegate

HKS Manifold Test Fit

Day 13

Q45 Throttle Body

Silicone Connector Tips/Tricks

Intercooler Cold Pipe

Day 14

Turbo Clock

Link to comment
https://www.sau.com.au/forums/topic/171375-found-an-awsome-site/
Share on other sites

240z ? but anyhow, some useful general info in there.. Looks like you have to swap the sump for a 240

To go into an R32.. you don't need custom mounts, you can just use the existing RB20det ones. Unbolt them, and bolt them to the rb25..

Thats where it went!!!

That used to be another site and was extremely useful, i had it on my favourites list, a few months ago however it disappeared and the link was broken. He must have take it to another site!

Thanks for linking it, very useful info.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes the gear for the R33/34 is different, it is red and has a different number of teeth. My part didn't come with that gear though, so I don't know how many teeth are on the red one. You'd have to reuse the 260RS/R33 gear, as long as it's not destroyed.   Haha, as unfortunate as that might be it was working fine for about the first 1500km I've had the car for now.
    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
×
×
  • Create New...