Jump to content
SAU Community

Recommended Posts

I've done a search but can't find my answer...

- Is anyone running 17x9 all round? specifically on an R34 GTT

- Will 9" fit the front? seems most people go for 8"

- Can I go for the same width AND offset for front and rear? I was thinking 17x9 with offset in the range of +30 to +35.

specifically for a 34 GTT and only 17"

cheers

The offsets seem a bit too low.

if it's for a GTT

17x9 +20 is definitely not too low offset, IMO i wouldn't touch anything with a higher offset than that. Hell, i'm going to be running 17x9 +0 and 18x10 +12 on an S13 soon, will look tough as!

Hi guys just need some help while on this topic.

Ill looking at buying 18inch wheels with 18x8.5+43 Rears 235x40 & 18x8+41 Fronts 225x40.

Will these offset fit my R34 gtt?

Would it clear the brakes?

Thanks guys

Please don't, those offsets will look like complete AIDS on a R34

Edited by ~Hypnotik~

jesus this thread is a brothel!

you can run way better offsets than have been mentioned here...

i run 18.9.5 +30 (18x8.5+30 front) on an r33 gtst with no flare and near flat camber (just a roll) and its an easy fit... the 34 guards are bigger again, so 9.5 +20 will get you about the same fitment as me, and i still could go out a bit more... say another 10mm before i need to flare

DSC00011.jpg

Most people are way too conservative with offset. 33's can definitely fit +20 9.5" rims at the rear and +20 8.5-9 at the front with guard work and it will look a huge deal better than +35 and above offsets. Just don't run bulgy oversized tyres. 265-275 for 10", 255-265 for 9.5", 235-245 for 9", 235-225 for 8.5", 225-215 for 8". Any lower width and the rims are no good for a turbo skyline.

  • 2 months later...

R33 GTST easy but wide fit would be:

Front = 18 x 8.5 +30 235/40/18

Rear = 18 x 9 +30 245/40/18

A little roll at rear - with 1degree neg camber both front and rear.

Keep in mind that you don't want big changes in track widths front to rear.

R34 are a bit bigger so:

Front = 18 x 8.5 +24

Rear = 18 x 9 +24

Not that I can think of rims that are these exact sizes. I currently have 18 x 8 +30 and 18 x 8.5 +33 and they sit about 1cm too far in the guards on R33. Come tyre replacement time I will get 245/40/18 for the rear - up from 235/40/18.

Edited by simpletool

Hi,

I have not been sharing much since i came on the forum. I am from malaysia and here what i have for my setup.

18x9.5 +12 all around

F: 225/45/18 -1 camber

R:245/40/18 -2 camber

[ wheel was off a R34 GTR, got it cuz it was dirt cheap and thought the offset should be manageable]

I have not flared my guards so i been scrapping on hard bumps on all 4 wheels for a few weeks now. I am looking to get camber arm to help go negative even more. This is the part i need some guidance on. Now i have jacked up the suspension so the scrapping is to the minimum. There is a few people in here i have PM that helped me; it still work in progress.

post-51211-1248662237_thumb.jpg

Edited by k20aek

im running 18x8.0 on the front, unsure of offset i'd have to check with 235 rubber no guard work

and 18x9.0 +24 with 265 tyres no guard work.

back wheels sit flush, maybe stick out a mm or 2. looks good

thats on r34gtt

Edited by stenve
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
    • Murphy strikes again! Nothing at all would have gone wrong if you had the tool kit in the car! You'd have just found the clamp loose the next time you went to touch it...
    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
×
×
  • Create New...