Jump to content
SAU Community

Recommended Posts

DSC05526.jpg

the big yellow one?

my standard oil pressure gauge was showing low readings yesterday morning (1 at idle - 2 when driving)

then after being parked for 30 mins, the gauge showed normal readings (2 at idle - 4 when driving)

than again a few hours later the readings were low again.

i suspect (hope) it's the standard sensor playing up.

EDIT:

i cleaned the plug terminals with contact cleaner. they were clean anyway.

the gauge is now showing kinda normal readings, just a tad low on cold start. it use to creep up to 5-6 on the stock gauge, now it goes just over 4.

at about 3000rpm, warm, its just under 4. this is a bit lower than it used to be. idle is a touch under 2, as before.

my question is, is there something that would actually cause low oil pressure (1 at idle - 2 when driving), and then recover from this?

or is this almost certainly a gauge/sender fault?

i plan on getting an aftermarket gauge, but sandwich plate etc, it's gonna take a while. i'm guessing you have to drop the oil in order to do this. no way around it?

Edited by Munkyb0y

i cleaned the plug terminals with contact cleaner. they were clean anyway.

the gauge is now showing kinda normal readings, just a tad low on cold start. it use to creep up to 5-6 on the stock gauge, now it goes just over 4.

at about 3000rpm, warm, its just under 4. this is a bit lower than it used to be. idle is a touch under 2, as before.

my question is, is there something that would actually cause low oil pressure (1 at idle - 2 when driving), and then recover from this?

or is this almost certainly a gauge/sender fault?

i plan on getting an aftermarket gauge, but sandwich plate etc, it's gonna take a while. i'm guessing you have to drop the oil in order to do this. no way around it?

Hmm interesting, i used to get similar things with really low oil pressure. It would only do it now and then, like once a week. I would be sitting at a traffic light or something and then suddenly my oil pressure would go down to like zero and id be like ;) but there were no signs of any problems so i never thought much of it. Hmmm might check my sender aswell.

Where is the actual sender located? Im looking at that pic and have no idea where that is??? (Below the intake runners??)

Edited by PM-R33
my question is, is there something that would actually cause low oil pressure (1 at idle - 2 when driving), and then recover from this?
How much oil is in the sump? How old is the oil? What grade is the oil?
How much oil is in the sump? How old is the oil? What grade is the oil?

less than 1000kms old. 7.5w30 genuine nissan semi-synth. dipstick shows full. car has never used oil between changes.

the stock sensors are renowned for being crap (in the GT-R anyway), mine goes to 0 sometimes (freaked me out the first time). But all i do now is flick the engine off and on, and the gauge works again. I'm gunna get a quality aftermarket gauge, as i don't trust mine as far as i can kick it.

I am in the same boat. One second it sits normal, then it drops to 0. Scared me to death eh.

How difficult is it to get to that oil pressure sender unit in the pic? I can picture it, but i have hands bigger than dinner plates, so it's super hard for me to even get my hands around the oil filter.

Yeah well you could all be like me..... thought yeah its just the sender , they are all crap and a common problem.

BUT, on rebuilding the motor from continuing driving when the screws had come out of the back of the oil pump and impossible to see,

it was REALLY the oil pressure being almost non existent that caused the big ends to start knocking and burning!

I certainly would not wish that on anyone so hope thats not your problem!

Maybe you should do what my son suggested and fit a proper mechanical Oil Pressure gauge and avoid the end disaster. :dry:

Can u just replace the sender or something? Its just i allready have 2 gauges in my car in a pillar, and would rather not get another gauge (oil pressure) to just chuck somewhere on the dash. If its just the sender, would a new sender fix the problem instead of getting an aftermarker oil pressure gauge?

you can change the sender, but you'll need a nissan or nissan compliant sender. otherwise the values it's sending wont be correct for the gauge.

just like you cant hook up an aftermarket gauge to the standard sender and expect it to work correctly.

i'm not too sure, but have read that the nissan sender costs quite a bit. defi gauge price range :D

my question is, is there something that would actually cause low oil pressure (1 at idle - 2 when driving), and then recover from this?

or is this almost certainly a gauge/sender fault?

i plan on getting an aftermarket gauge, but sandwich plate etc, it's gonna take a while. i'm guessing you have to drop the oil in order to do this. no way around it?

????? :)

i have a mint sender if anyone wants to make an offer on it.

it might be the sender, it might also be the dash guage.

at the end of the day unless you put a mechanical guage on it, you will not really know the pressures for sure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...