Jump to content
SAU Community

Recommended Posts

Dave,

good work on finding a fix for the clicking noise, I have the same problem on my r32 gtr and was planning on buying a second hand attessa unit and fitting it to my car. After reading this thread I will now just try and re-charge the accumulator that is currently on the car. Just a a quick question, what presssure did you fill the accumulator to? I read on the aristo link you posted that 1000psi seems to be norm for those cars, is that same pressure you used on you accumulator?

Thanks

Aki

  • 4 weeks later...
Problem solved!

So here's the solution if you have this clicking relay problem (and it is because of the "flat" accumulator - probably is though):

- with engine/ignition off, open hydraulic bleeder connection on the underside of the ATTESA assembly (just above the rear diff')

- unscrew the accumulator, may lose a few drops of ATTESA system fluid?

- recharge or replace the accumulator

- replace the O-ring on it if it is looking cracked

- screw back in :O

So far mine is fixed, no 4wd light, and the relay clicked only perhaps twice(?) that I noticed on a 45+ minute drive. At last got rid of that infernal clicking!!!

PS For those looking for a way to get their cylinders recharged... check out this forum topic (sorry mod's it's on a Toyota forum - don't think there's any conflict of interest there though!). I'm just about to send the guy who does the recharging ("Mooty") my flat accumulator cylinder, to use as an exchange unit, and he says he will soon get back into the recharging and do ATTESA too. So hopefully we will soon have access to an exchange service which can recharge the cylinders for under $150 :)

I have been chasing this problem for 4 years and just fixed it 2hrs ago!

Big thanks to Dave B for finding the fix.

Just replaced my accumulator and no more ETS relay clicking in the boot! I replaced mine with a secondhand one but they are available new from Nissan.

Big thanks to Ben from Quatromotive in Northgate Brisbane who can source the accumulator and remove & refit!

http://www.quattromotive.com.au/

Cheers Dave B happy as :)

Dave,

good work on finding a fix for the clicking noise, I have the same problem on my r32 gtr and was planning on buying a second hand attessa unit and fitting it to my car. After reading this thread I will now just try and re-charge the accumulator that is currently on the car. Just a a quick question, what presssure did you fill the accumulator to? I read on the aristo link you posted that 1000psi seems to be norm for those cars, is that same pressure you used on you accumulator?

Thanks

Aki

Great stuff guys, good info' on the units from Nissan and I will have to check out that web address... sorry I missed your reply Aki but in answer to your question: I don't know what the pressure is because I replaced my accumulator with a used, known-good second-hand unit. 1,000PSI sounds like a lot but could be right. Hopefully if there is a place who can recharge them they will know.

I have been chasing this problem for 4 years and just fixed it 2hrs ago!

Big thanks to Dave B for finding the fix.

Just replaced my accumulator and no more ETS relay clicking in the boot! I replaced mine with a secondhand one but they are available new from Nissan.

Big thanks to Ben from Quatromotive in Northgate Brisbane who can source the accumulator and remove & refit!

http://www.quattromotive.com.au/

Cheers Dave B happy as :blink:

Great news! Glad it worked :)

  • 2 months later...

Its so funny cause i had the exact same problem and so many people on the forums said it was normal.

I remember when i first got my Gtr34 it never used to do this clicking thing in the boot and then after the first engine failed the car sat for so long so i presume thats when the accumalator lost its pressure ...

Then when i got the second motor in and started driving her around town running it in i remember pulling up to a robot and hearing this constant clicking sound it used to bug me terribly.

So i posted a few questions and never had them really answered.

I even used examples of other gtr34's attessa system pump sounds and never was the relay noise ever mentioned.

As fas as i know the pump should engage once when the car is just been started and then you wont hear it again till some track use or hard driving with some major turning and high speed cornering then a few seconds later after you stop and let the car idle you shouldnt hear the relay clicking you should actually hear a pump high pitched whine coming from the rear of the car and that means its charging up the attessa accumalator.

Thankyou for taking the time and pain staking process of trying to solve this problem.

I remember on gtr.co.uk there is a guy there called joker69 or something like that he also had the same problem and replaced his attessa accum.... and viola problem solved amazing.

i would still suggest bleeding the system after fitting the new unit as you will get air trapped in the system and bleed the whole system starting from the resevoir and then the pump at the back and then finally the front Bleed nipple that is next to what they call the clutch pack on the front transfer case.

Thankyou again when i get my car on the road again maybe in a year or so i will post when i replace the accum and let you guys know what results i get as well.

Cheers and well done...

thanks everyone for the info, ordered a new accumulator from Nissan today, $380, and a new relay to be sure $40. Didnt want to take a chance on a 2nd hand unit as they are all over 10 yrs old by now. But seems to be an opening for a business if they can get a recharge service going.

  • 2 weeks later...
Problem solved!

So here's the solution if you have this clicking relay problem (and it is because of the "flat" accumulator - probably is though):

- with engine/ignition off, open hydraulic bleeder connection on the underside of the ATTESA assembly (just above the rear diff')

- unscrew the accumulator, may lose a few drops of ATTESA system fluid?

- recharge or replace the accumulator

- replace the O-ring on it if it is looking cracked

- screw back in :)

So far mine is fixed, no 4wd light, and the relay clicked only perhaps twice(?) that I noticed on a 45+ minute drive. At last got rid of that infernal clicking!!!

PS For those looking for a way to get their cylinders recharged... check out this forum topic (sorry mod's it's on a Toyota forum - don't think there's any conflict of interest there though!). I'm just about to send the guy who does the recharging ("Mooty") my flat accumulator cylinder, to use as an exchange unit, and he says he will soon get back into the recharging and do ATTESA too. So hopefully we will soon have access to an exchange service which can recharge the cylinders for under $150 :P

wow, thank you so much!! i had the same problem for the last 4 years with no repercussions. but the last 2 weeks, its getting worse and worse, it clicks every 5-10 sec and, i loose power steering, radio shutdown, my apexis panels shut down and my lights flicker every where !!

my car is getting new turbos and i asked my mechanics to change my accumulator at the same time !!

Its gonna be weird not hearing the sound anymore after 4 years of annoying clicks.

Marc-André from Montréal, Canada

got the accumulator ready to install, for those who have done this, what tool did you use to remove it? oil filter wrench ? and could you turn it/get leverage without lowering the diff ?

got the accumulator ready to install, for those who have done this, what tool did you use to remove it? oil filter wrench ? and could you turn it/get leverage without lowering the diff ?

Definitely can do on the car, without removing anything (well having a hoist obviously made it easier). I removed one using a G-clamp; but perhaps you could even get it undone using an oil filter wrench... I can't remember what the mechanic used who undid mine on the car but it may have been an oil filter wrench.

  • 4 months later...
  • 3 weeks later...
  • 3 weeks later...

update:

Replaced the actuator 6 months ago due to the relay clicking, new from nissan.

All fine until a month or so ago, clicking stated up again, but only on hot days and only after driving for more than approx 30min. And even then, doesnt always happen, maybe on 1/3 of long drives. The clicking occurs rapidly on accel and when snow button is pressed whilst idling. If I turn off/on engine for a few minutes it come good. This all matches the pattern i had before i replaced accuator. I would have thought if actuator went, it wouldnt be an intermittent problem, but always ? For those who fixed theirs with actuator, was it clicking at all times ?

Not keen to spend another $350 on a new actuator.

It appears heat related, possibly pump or electrical ? Any ideas. And yes, new fluid, bled many times from both nipples...

  • 3 years later...

Hi All,

Anyone removed the accumulator without lowering subframe/diff?

I tried this today on my R32 Gtr and couldnt get a good grip on the accumulator with G clamp.

The accumulator seems to be stuck/seized at the thread.

Any advice is helpful thanks.

Edited by keysersoze

When I said "I" removed it, that was a bit of a furby... I watched the mechanic do it with the car on a hoist. I have a vague recollection of him scratching his head for a couple of minutes, and saying something like "hope we can do this without dropping the diff", but then I pretty clearly remember it only took 5 minutes so no diff removal just a bit tight.

Glad this has cropped up. The Dayz has the dreaded "Click" Did not know what it is. Now I know how to fix. Many thanks.

Edited by 66yostagea
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...