Jump to content
SAU Community

Whats Wrong With My Car!

walta

By walta,
in Engines & Forced Induction

 Share

Recommended Posts

walta Explorer

walta

Posted
Posted

R33 Series 2, GTS-T Manual, stock apaprt from turbo back exhaust & k&n POD filter

ok, still hesitating/surging after 4500rpm, cant work out what it is, so far the following has been replaced (not neccisarily to fix this problem)

fuel pump, plugs, coil packs, fuel filter, timing belt, water pump, k&n filter, clutch, injectors cleaned, serviced, turbo back exhaust

it went on the dyno yesty and it showed no change in the air/fuel mixtures when it was surging,

so is it coil pack igniter module thingy? timing? ?????????

Link to comment
https://www.sau.com.au/forums/topic/178121-whats-wrong-with-my-car/
Share on other sites
walta Explorer

walta

Posted
  • Author
Posted
what heat range plugs?

what gaps?

coil packs new?

you haven't mentioned anything about the AFM.

i know the plugs are platinum ones, the gaps are right and the coil packs are new (splitfire)

i thought if the air flow meter was playing up it would of shown a change in the air/fuel mixtures when it was surging???

walta Explorer

walta

Posted
  • Author
Posted (edited)
get rid of the platinum plugs. they are terrible.

get coppers (part number bcpr6es) or iridiums. if you get iridiums make sure they are gapped to 0.8mm and heat range 6.

ok they may be crap, but could they be actually causing the problem? especially this noticable.

Edited by walta
sweetr33 Experienced

sweetr33

Posted
Posted

slose gapped plugs shouldnt be required if you got new splitfire coils, should have ample spark to jump even the stock 1.1mm gap... look elsewhere for your problem, disconnect each coill pack via the plug and reconnect n go through the list as its running to varify which cylinder has the miss and work from there

foznice Veteran

foznice

Posted
Posted
slose gapped plugs shouldnt be required if you got new splitfire coils, should have ample spark to jump even the stock 1.1mm gap... look elsewhere for your problem, disconnect each coill pack via the plug and reconnect n go through the list as its running to varify which cylinder has the miss and work from there

I agree, its not like your running monster boost or anything. I would have thought stock gap would be fine, but if it isn't, mabye becuase of your exhaust, then I wouldn't really think that you'd need anything smaller than .08mm.

Crash. Enthusiast

Crash.

Posted
Posted
Hey guys

Just throwing this out there but could it be something to do with the CAS??

Yes, i was getting a bad miss on mine, tried a few things like coil packs, AFM, spark plugs, etc....

Got a CAS from another skyline and put it on mine, miss was gone. Grabbed a 2nd hand CAS and threw it on.

walta Explorer

walta

Posted
  • Author
Posted
Yes, i was getting a bad miss on mine, tried a few things like coil packs, AFM, spark plugs, etc....

Got a CAS from another skyline and put it on mine, miss was gone. Grabbed a 2nd hand CAS and threw it on.

whats a CAS by the way? LOL

r33cruiser Grand Master

r33cruiser

Posted
Posted

hi just throwing it out there.

i read on boostcruising that all skylines that rev towards the 5k range or reach the 10psi reigon suffer from flat spots. what they did was install a apexi safc, and it works perfectly now.

just throwing it out there. good luk

:):)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Question about BoV on RB25DET NEO

      By GTSBoy · Posted

      It's not as simple as it is being made out to be. It s not hard, but there are things that have to be done. Am busy right now, but will try to essay later.
    • joshuaho96
      Question about BoV on RB25DET NEO

      By joshuaho96 · Posted

      Pinout is different to my knowledge, but you should confirm to be sure. Also you will need to adjust the VQ table in Nistune to suit. I would still recommend sticking with recirculating BOVs, I'm not sure if the R35 card MAF will fully resolve stalling caused by reversion/throttle lift.
    • Kapr
      Question about BoV on RB25DET NEO

      By Kapr · Posted

      What issues are those? Previous owner said it wants to stall sometimes. We did test drive and it was nice and smooth so it will be sporadic or idk. And if i just change MAF(the sensor to R35 version) it should be better? And as i asked...is it like "plug n play" with oem MAF from R34?  This is a MAF from R35 right?
    • joshuaho96
      Question about BoV on RB25DET NEO

      By joshuaho96 · Posted

      Even with no BOV you will have issues unless the MAF is a hot film type like the R35 which has some design features to deal with reversion. Hot wire MAFs are very sensitive.
    • Kapr
      Question about BoV on RB25DET NEO

      By Kapr · Posted

      So i just change the (whatever is inside ma original MAF and slide the R34 MAF (it is gonna fit right in? ) and somewhere on the hot side a BoV...i presume that would be vented to the atmo? I just "trying" to understand...maybe my mechanic would know this   I would not mind(even prefer) to run stock BoV cuz it is way more than fine but i do not have that and only pipeing what is left is oem J pipe ... I will be running Blitz fmic(to fit oem one side style) and i gonna need custom pipes cuz i do not have rest of those pipes and hoses... But i am want standalone ECU. Only choice i have atm is Nistune...but that is not gonna cut it right?I dont know what Nistune can and cant do... I know you guys know Link and Haltech...but whatabout ECUmaster? I know guys in here run those but i literally do not know about that and do not know differences... Just know to take whatever "my" tuner can work on.  
×
×
  • Create New...