Jump to content
SAU Community

Recommended Posts

  • Replies 223
  • Created
  • Last Reply

Top Posters In This Topic

I think it's time to have another go at this myself.

So I'll bring the camera gear as per normal but yeah have a bit of fun as well.

New rims, rubber, springs, swaybars, clutch, cv's, rebuilt gearbox in past 2 months

might as well see what they do.

can we have a FWD class this time :D

Will the entry form be available from anywhere other than sau? I can't access sau from work.

I can access the wrx forums if it will be on there.

I volunteered on the skid pan most of the day last time.

When the forms go up ill add non forum.* mirror

I probably won't be entering...I was asking on dez's behalf...He volunteered on the skid pan all afternoon...

he said he's still gonna try and get a spot normally though...

Yep, let Dez know he's in. Tell him to still get an entry form to me ASAP.

We might also be short on officials this time round.

So if your coming up for the day and can lend a hand (especially on the back track and mini-wang in the morning), then please let me know.

We need about 8 officials in total, doing starting x2, timing x2, finishing gate x2 and chicane monitoring x2.

23 Members: d00dz, evade, ferni, paulr33, Do-Luck, THEGME, Rowdyr32, Blade, gazoom, HKS-R33, RCHOO, Russman, sarahB, map7, lamps, ziad, Belsil80, kasanoff, Scotsman, sammus, Random Dude, ~sarah~, NYLATE

NSW FTW

I'll be faxing this when I get home from work. Paid $75 into the account already

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...