Jump to content
SAU Community

Recommended Posts

Ok well thats good and bad news :( Good news its actually chipped bas news its not nistune :(

So how am I able to tune this ecu? I was going to buy a consult cable but now it looks like my ecu is not easily tuneable

Does anyone know who chipped my ecu? like what brand or whatever? cheers for all your help

No it doesn't have a nistune. I has been chipped though... Its got a socket with UV eraseable EPROM

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5615513
Share on other sites

Ok well thats good and bad news :( Good news its actually chipped bas news its not nistune :(

So how am I able to tune this ecu? I was going to buy a consult cable but now it looks like my ecu is not easily tuneable

Does anyone know who chipped my ecu? like what brand or whatever? cheers for all your help

the same way any other chip is done, find someone with a chip eraser etc, its crap though takes ages to get any real changes, just fork out for a nistune, about $300 installed usually and maybe 2-800 for a tune depending how many mods, if its basically stock they prob have a good base map and only need 30mins touching it up.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5615943
Share on other sites

Question.

Will a map burnt to the Nistuned ecu be wiped if you disconnect the battery terminals (i.e. the method for resetting the factory ecu)?

No, just like the factory one it will simply revert to the programmed maps, deleting any self adjustment the ECU had made to fuel and ignition maps.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5621785
Share on other sites

Question.

Will a map burnt to the Nistuned ecu be wiped if you disconnect the battery terminals (i.e. the method for resetting the factory ecu)?

The factory ecu doesn't really learn much, it has a knock map and a normal map, all you really reset is the ecu flags which if accurate will be restored on reset anyway.

So no it doesn't reset anything more than it currently does.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5621909
Share on other sites

  • 2 weeks later...

I received my nistune stuff last week :)

When you order it they ask for ur ecu number on the casing, Now is this to put a stock standard base tune on the chip?

So if I install it, would the car drive/idle like the stock ecu ? Is this fine for the car?

Or is driving around with the nistune chip in the car before it gets tuned a big no no?

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5638520
Share on other sites

They ask for ecu number incase you have an ECU they haven't seen before or can't use (R33 GTR ECU for example), the stock map is pre-loaded (100% the same as the factory map) and will be exactly like driving with an unmodified stock ECU.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5638545
Share on other sites

I received my nistune stuff last week :)

When you order it they ask for ur ecu number on the casing, Now is this to put a stock standard base tune on the chip?

So if I install it, would the car drive/idle like the stock ecu ? Is this fine for the car?

Or is driving around with the nistune chip in the car before it gets tuned a big no no?

Be like you hadn't done anything to it, they will load a stock map on for you, if it was the wrong map or untuned there is a high likely hood it wouldn't even idle so you couldn't do much damage.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5638548
Share on other sites

  • 3 weeks later...

Matt, I think one our WA guys has been given a bum steer.. I know you do board for auto series 2 Stageas and I was fairly certain you do board for manual series 2 Stageas (RS4S) however he received this reply..

Hi Mike,

Thanks for contacting ***.

The Nissan Stagea RS4S Series 2 with manual transmission has an ECU which is currently not supported by NIStune Software.

Feel free to contact *** should you have any further questions.

Pretty sure he has a 0V801 ECU, can you please confirm? Would have sent you an email but I'm at work :P

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5665967
Share on other sites

Matt, I think one our WA guys has been given a bum steer.. I know you do board for auto series 2 Stageas and I was fairly certain you do board for manual series 2 Stageas (RS4S) however he received this reply..

...

Pretty sure he has a 0V801 ECU, can you please confirm? Would have sent you an email but I'm at work :P

The guy has been misled. MT SII RS4S is supported by Nistune for more than 3 years now.

I'm using exactly 0V801 ECU with nistune and have a mate here who's using Type 4 board programmed with 0V801 image in his AT ECU. Neo ECUs are actually interchangable - I was running RWD R34 ECU (AA500) with my Stagea motor for two months with no problems at all.

Link to comment
https://www.sau.com.au/forums/topic/181930-nistune/page/17/#findComment-5667436
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...