Jump to content
SAU Community

Bad Design In Cars

donut_kng

By donut_kng,
in General Automotive Discussion

 Share

Recommended Posts

  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

floody Experienced

floody

Posted
Posted

Heater box positioning. Placing an extremely expensive, non serviceable item prone to leakage where it generally is impossible to access without removing effectively half the interior, and is guaranteed to at some point leak and spark off rust issues in the floor pan, is pretty stupid really.

Everything on the intake side of the HR31 RB20DET; it is near impossible to access anything on that side with the gearbox in, in fact most things would be easier with the engine out. That doesn't just go for the complex network of sensors and vacuum actuators, but also for things like the oil filter. I believe its mostly due to the short deck height and extreme width of the head, which puts the bulky intake very close to the strut tower. RB25s and RB30s in the same engine bay are nowhere near as bad.

VB- Veteran

VB-

Posted
Posted

alot of cars i get into with manual window winders, i find the winders are facing up when the window is right down, and sticks into the side of my knee. frustrating when just trying to cruise with the window down, i either have to put the window up a lil and have it sticking into the underside of my arm, or leave it down and have the winder in the side of my knee

zebra Grand Master

zebra

Posted
Posted
I just realised this morning that the 32's handbrake position is shit. You can't have your car in reverse and push the handbrake button down easily. Just say you are on a hill and need to reverse out. The handbrake is a bit close to the gearstick.

+1 For That in my 33....the long ass gear leaver in my car touches the handbrake in reverse

Kinks Grand Master

Kinks

Posted
Posted
My R31 looks like a fridge on wheels.

In my experience, fridges often have beer in them. I don't see the problem?

Re R33 antennas, mine went crazy one day and went all the way up on half. i turned it to full, and nothing happened. turned it back to half and it went all the way in. turned the radio off and then back on again and it stayed in. turned it to full and it went all the way up.

a day later it mysteriously fixed itself and went back to normal :laughing-smiley-014:

R33 has very, very few things that bother me. They are a well sorted car.

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted
alot of cars i get into with manual window winders, i find the winders are facing up when the window is right down, and sticks into the side of my knee. frustrating when just trying to cruise with the window down, i either have to put the window up a lil and have it sticking into the underside of my arm, or leave it down and have the winder in the side of my knee

+ 11ty

Richie33 Contributor

Richie33

Posted
Posted

The R33 cup holder isn't movement proof, its got that thing for holding cans but no support at the front. Even under gentle braking I've had it fall out.

Boot space is shocking in the 33 for a car it's size, it just fits 2 sets of golf clubs... just. Victim of having the fuel tank between the rear seat and boot.

Kinks Grand Master

Kinks

Posted
Posted

People quickly learn that anything not bolted to something else in my car, moves. I don't leave drinks in the console for the same reason, besides which it's not deep enough and it gets in the way of changing gears. I suppose that's a minor annoyance but it doesn't bother me *shrug*

Boot space is pretty bad but I think it is designed for the jap businessman who only needs to carry golf clubs.

  • 2 weeks later...
Kinks Grand Master

Kinks

Posted
Posted
Re R33 antennas, mine went crazy one day and went all the way up on half. i turned it to full, and nothing happened. turned it back to half and it went all the way in. turned the radio off and then back on again and it stayed in. turned it to full and it went all the way up.

a day later it mysteriously fixed itself and went back to normal :laughing-smiley-014:

f**king jinxed myself, now it has shit itself good and proper :happy:

Cassbo Grand Master

Cassbo

Posted
Posted
Electronic throttles suck balls.

Oh doesn't it. My driving style dictates that to slow my car down while going down a hill that I push in the clutch, hit the accelerator for a moment, then shove it into a lower gear. Works just fine with a cable driven throttle. Electronic ones don't quite have the response I like... and I don't enjoy compression lock up in a front wheel drive Volkswaggen Caddie...

The beverage holder in the R33 seems pretty useless, mainly because I'm always changing gears. Its usually my mobile holder, and it does that pretty dismally too lol

Reverse in Euro cars, I want it under 5th or next to 6th, not next to 1st.

Wiper/Indicators in Euro cars, wrong way around :wave:

Anything with over 120kWs and front wheel drive... Magna, 380, Aurion (although, its ment to be pretty good lol), Camry, ect. Torque/under steer... Plus, I want a tail shaft damn it!

No dimmer for the dash illumination in my R33. Sure, not needed in the city, but when I go bush and there is wildlife near the road, I want full concentration on the road :D

The fuel consumption thing in BMWs. OMG!! Distracting :D Wants an on/off button.

Over use of plastic in engine bays.

Plastic throttle bodies designed for climates around Britan and such. Got 3000rpm idle?

Overly powerful power steering. I like to feel some effort.

tricky_dan Enthusiast

tricky_dan

Posted
Posted

BG model Mazda 323s - the A pillar plastic trim always goes brittle and falls off, and you cant get them second hand because they break as soon as you try and take them off :yucky:

Surprisingly, +1

definently +1! haha ive owned 2 BGs, the first one was mint and had them (but wrote the car off...) but my current ones are totally broken!

oh and the oil filter in BGs is also a real bitch.. not sure how it compares to rb26s tho..

apex seals in rotarys? i really wish all cars were rotaries (cause they just keeep spinning) but those bloody apex seals....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...