Jump to content
SAU Community

Recommended Posts

Generally means one bulb is out, or technically, there is not enough resistance in the system.

Checked all the bulb, and/or installed LED lights anywhere?

Thats about it from my experience.

Ok so the full story is that it was dying a slow death. I'd indicate and three click in I'd get two fast ones, then three good ones again. I figured that was the sign for "replace the globe", since it was on the rear left that wasn't working. So I did, but it didn't change anything, and now a few days later, it just clicks fast all the time and I have no indicators on the left hand side.

Sorry, read this and I didn't post.

Have you got the indicators in your mirrors?

I had similar behaviour from mine when I picked it up from the alarm installer, ended up they'd knocked the wiring for the mirrors, and because they're scotch locked into the main harness the scotch lock had cut through the wiring.

Wiring is down in the drivers footwell, behind the panel forward of the door.

Not sure if that's what it is, but worth checking. It was flashing fast all the time and I had no indicators in the left hand side, but the LEDs in the mirrors did.

Sorry, read this and I didn't post.

Have you got the indicators in your mirrors?

I had similar behaviour from mine when I picked it up from the alarm installer, ended up they'd knocked the wiring for the mirrors, and because they're scotch locked into the main harness the scotch lock had cut through the wiring.

Wiring is down in the drivers footwell, behind the panel forward of the door.

Not sure if that's what it is, but worth checking. It was flashing fast all the time and I had no indicators in the left hand side, but the LEDs in the mirrors did.

I'm not finding much. >_<

Mine doesn't have the mirror indicators so I may be barking up the wrong tree.

Actually, thinking in the same mindset of Ryan's situation (cable slowly being "pulled" or broken, which makes sense in my situation), is there a cable from the ECU that would stop the indicators working for just one side of the car? I did do the wire snip mod on the same day as the indicators started becoming intermittent.

Ah ha!

Found this document (not sure if it's really that relevant), but it at least pointed me in the right direction..

http://www.psedog.com/cars/fsm/g35/coupe/2003/bcs.pdf

Went searching and found that there's a pink and.. yellow? cable down there that had some electrical tape around it. Seemed a bit suss, so I took the tape off and sure enough the solder had come undone. I suspect that when my alarm was installed the installer cut this wire by accident and soldered it up but while I've been under there it's come loose. Anyway it's all fixed up and working now so I'm stoked! :thumbsup:

Ah ha!

Found this document (not sure if it's really that relevant), but it at least pointed me in the right direction..

http://www.psedog.com/cars/fsm/g35/coupe/2003/bcs.pdf

Went searching and found that there's a pink and.. yellow? cable down there that had some electrical tape around it. Seemed a bit suss, so I took the tape off and sure enough the solder had come undone. I suspect that when my alarm was installed the installer cut this wire by accident and soldered it up but while I've been under there it's come loose. Anyway it's all fixed up and working now so I'm stoked! :thumbsup:

Awesome, good work!

Hmmm turns out I didn't fix the problem.

If the BCM was stuffed, would it permanently not work? Or be intermittent? Intermittent seems like a cable contact issue don't you think?

Are the BCM's easy to swap in and out? Is it just a matter of unplugging it, putting the new one in and plugging that in? If I can borrow another one just to test it would certainly make troubleshooting a lot easier.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...