Jump to content
SAU Community

Recommended Posts

  • Replies 812
  • Created
  • Last Reply

Top Posters In This Topic

I was thinking (which is dangerous)

Have you had a chance to weigh the front and rear seperatly of a R32 gtst to compare it to your ls1 powered jobbie...would be interesting to see how far the weight has gone rearward with the lighter motor but heavier box, GTR diff etc

we know that complete ls2 weighs 90kg, we weighd rb25de today and it maxed out the scales so 120kg+

I was thinking (which is dangerous)

Have you had a chance to weigh the front and rear seperatly of a R32 gtst to compare it to your ls1 powered jobbie...would be interesting to see how far the weight has gone rearward with the lighter motor but heavier box, GTR diff etc

SO Judging from what I remeber the weight balence is standard. you should be very damn close to 50:50 front to rear.

I cant believe how light the Ls1's are 30+ kgs lighter than an RB25de is quite suprising so that would prob be more like 50+ kgs over a DET once you include The IC + Piping etc and not to metion all that hangs right at the front of the car.

yeh it is at least 30kg as that was the max the scale would read, and it was short steer pump and exhaust manifold.

weighed r33 tubo box today and it went 57.5kg. i was very surprised as i thought it would be lighteras thats only 5kg lighter than the tremec 6 speed.

so i think i am up somewhere between 35-55 kilos in the driveline which i am very happy with.

basically this means that the car should be easier to make handle and my power to weight is up.

1000kg and 400hp is looking good.

SO Judging from what I remeber the weight balence is standard. you should be very damn close to 50:50 front to rear.

I cant believe how light the Ls1's are 30+ kgs lighter than an RB25de is quite suprising so that would prob be more like 50+ kgs over a DET once you include The IC + Piping etc and not to metion all that hangs right at the front of the car.

ok, just read the whole thread..(phew!)...nicely done indeedy...now.. if someone wants a 31 or 30 to put a v8 in..call me...anytime :O

interesting on the weight differences, who'd have thunk it eh?!!!

cant wait to see full pics and vid!!!

Not too much to report, recieved coil-overs from Gary last week. just waiting for the lower arms and bars and bush kits now which should have by friday so with a bit of luck i might have the car back on the ground on saturday arvo. Also close to purchasing front brake kit, so car will be pretty much a roller again. That will just leave engine completion, which i have all the parts for, wiring & exhaust. some fiddly bits to do also like tin-work and ducting. catch-cans etc..........neverending.

post-20078-1223934315_thumb.jpg

post-20078-1223934444_thumb.jpg

post-20078-1223934542_thumb.jpg

yeh, eye on the prize. keep putting myself behind the 8 ball though, finish one thing then find something else to buy. looking seriously at that intake again, tuner reckons there is free horespower to be had with being able to adjust runner lengths so it looks like it will be happening next. Also going to give the E85 a go as all the race meetings are sprints so consumption wont be an issue. Doing endurance events might mean 2 extra fuel stops.

Keep the end in mind Stu!

I might come past this week to talk the sphincter of the universe about servicing the golf........will let you know

i have no doubt there is more power to be made on E85, cooler intake temps coupled with higher octane levels allowing more agressive tuning, its the consumption that is the concern as i only have a 50liter tank. but if its OK for V8SC, im sure ill be fine.

e85 is a great idea....we might give that a shot too. we've got a drain valve on the fuel cell, and datalogit to switch the tunes easily....will be good to see how it compares

lol. that is pretty cool. finally get that decent engine into a decent chassis. :P I like it.

can't wait to see your thing rumbleing along stu. it will definitely rock.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...