Jump to content
SAU Community

Recommended Posts

Investigators aren't sure if the girls were wearing seatbelts, and witnesses are quoted as saying there was exessive speed.

Another P-plater tragedy, there are far too many of them.

As usual the driver only has minor injuries.

Well you can tell from the article that the car wasnt a performance car, as it wasnt listed there be the media

Probably a common family sedan or small car.

Goes to show the bullshit media in the country sensationalises things.

Sad waste of life, and a mockery to the road laws when any car can do 100km/h and unfortunately kill people.

This is very sad. I read it on the Herald Sun site yesterday before the second girl died. :thumbsup:

Another four families affected for the rest of their days by an idiot.

RIP to those involved.

The toll is 16 lower than this time last year but I doubt very much that has anything to do with publicity, probably more to do with the increase on the public transport network (think it said 30% in the last year, today).

Well you can tell from the article that the car wasnt a performance car, as it wasnt listed there be the media

Probably a common family sedan or small car.

Goes to show the bullshit media in the country sensationalises things.

Sad waste of life, and a mockery to the road laws when any car can do 100km/h and unfortunately kill people.

yep...we gotta remember the media are no experts in family cars, but they know their japanese imports.....

RIP to the deceased

I agree this is tragic. I'm not concerned if the driver was a P-plater, or if there was excessive speed involved, or if the occupants of the car were or were not wearing seat belts.

The point of raising this particular incident is that the government relies heavily on cameras, even changing the name from "speed" to "road safety" to try and justify them.

But a "safety camera" would not have detected the non-wearing of seat belts. And a camera, while it might have taken a photo of the behaviour prior to the incident, would not have prevented the outcome.

The only thing that stood a chance of preventing this tragic outcome was a visible police presence "on the ground".

It's time the government and all the so-called "road safety experts" realised this.

Being in the local area (the crash happened at the other end of my road) I can tell you that the police resources in this area are painfully thin, with 20 officers covering an area spanning north past Yea, east past Marysville, south past Powelltown and into Mooroolbark. They have little to no chance of providing any meaningful police presence on the roads out here and the locals know that.

yea this is very sad.. i once new of a girl that died when she snuck out at night with this guy and he was showing off and crashed hes R33 into a pole.. she died and he lived..

really stupid if u think of it..

fair enough risk your own life by driving fast but when u risk others lives.. really stupid..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...