Jump to content
SAU Community

Recommended Posts

if bench is weak... do more bench.

also for every push movement, do 2 pull movements.

does not work for wanking

Thanks for that, Yer i hear that you should counter the pushing. Face pulls are a good one apparently

Bench is a little on low side compared to squat (assuming thats below parallel in a rack). Just hit it more often with lower reps and eat. Elbows shouldnt flare out, keep them tucked in.

Yer thats what i didnt check when doing it, was alone also. Will have to get someone to look at me when there next.

Bench is a little on low side compared to squat (assuming thats below parallel in a rack). Just hit it more often with lower reps and eat. Elbows shouldnt flare out, keep them tucked in.

Elbows tucked in for bench? Ideally you want somewhere in between, tucking them in to far uses your tri's to much and is more a power lifting movement then one for building muscle.

I don't even care where my elbows are, unless I have an injury. Your body will have it's own form, different to everyone else's. Tucked in or not, whatever, none of that will stop you from getting strong in bench.

What do your sets and reps normally consist of for bench and how often a week do you do it?

Thanks for that, Yer i hear that you should counter the pushing. Face pulls are a good one apparently

Just stick to BB rows.

I find Pendlay Rows forces me to use good form.

Chins are also good.

Always start each rep by pulling the shoulder blades back first.

Elbows tucked in for bench? Ideally you want somewhere in between, tucking them in to far uses your tri's to much and is more a power lifting movement then one for building muscle.

I generalised my comment too much. By tucked in I don't mean 90 degress to your body or close to your body, somewhere in between like you said, I use about 45 deg. herpa derp on my behalf.

Jealous at all you runners & squatters...

Smashed out my traps today, awesomeness. And going to work on those Bird's-fingers;

might take a while tho! Nap time now, then study :(

I generalised my comment too much. By tucked in I don't mean 90 degress to your body or close to your body, somewhere in between like you said, I use about 45 deg. herpa derp on my behalf.

:cheers:

I can't do bench with a barbell anymore, hurts my shoulders for some reason, have to use dumbells instead, sucks having stronger shoulders then my chest, makes it hard to hit chest correctly :unsure:

how did you come to the conclusion that sore shoulder while benching with barbell = stronger shoulders?

The shoulder is a pretty complex joint/socket.

Lots of shit can go wrong with it and/or smaller muscles be left behind when other parts get stronger.

How strong are you with good form bent over barbell rows?

How is your shoulder mobility?

Pretty common issue with the bench/bro-press . I keep away from trying to bench heavy until my shoulders, back and triceps are ready for it.

As TTT said the shoulder mobility is a killer. If you have built the muscles for a strong shoulder girdle your bench will be stronger than without.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Perfect, I'll get to it this winter then at the same time as I weld on my anti squat kit. 
    • Alright so my 32 only has one temperature no matter what degree you set it to. I’ve tried disconnecting the servo motor arm and moving it either direction and got no change. I’ve fixed the leak in my AC and re charged it and with it on and clutch engaged it still blows hot even though the low pressure pipe going to the firewall is ice cold. Both heater core hoses are hot while running as well. Diagnostic code showed 24 for intake air temperature sensor. Anybody got any ideas?
    • I said Garrett style. Not Garrett genuine. And something in the G30 550 range is what you want. Not those pokey little old fashioned T28 sized things. The intake ports in the head are small. There is little benefit in fattening up the runners and leaving ths actual ports small. Just run what you've got. And on the subject of Nistune vs Haltech etc..... You know you can control the transmission with decent standalone ECUs these days, right? No need to keep any of that old Nissan bullshit. Don't get me wrong - I use Nistune on my Neo. But it is a DET, so the number of bodges and workarounds I had to do to make it work in a chassis without ABS, TCS, etc, is quite small compared to the herniated arsehole you will have trying to make it work on a motor that doesn't have some of the things that the turbo ECU wants to see. Just easier to bite the bullet and go aftermarket outright.      
    • Hmm. Only when the f**king thing is actually working. Still can't find the leak. And that's with dye being put in the last 3 times!
×
×
  • Create New...