Jump to content
SAU Community

Recommended Posts

how does everyone keep track of their workouts?

I use the Jefit app on my phone, keeps track of all my logs and lifts, can add notes if I feel the need and has made it easy to keep track of my workout volume.

Simple notepad file on tablet.

I run endomondo also to keep track of time spent and rest periods and check email, facebook during breaks and sometimes youtube clips on form.

I'm at home though so using a tablet to play my music and record notes doesn't seem as nerdy when you are flying solo.

Deadlift 220kg Birds. In your next deadlift session.. Do it once at least & receive a virtual high five.

You will do it ha ha...

No seriously lift 220.... I am confident you can do it.

Hahaha. Right now I'm confident I could get 200 up; I don't want to try it though, cause my form will be terrible. I'm currently fixing my form with more volume at lower weights for now, as my lower back was getting a bit sore with my "yanking" as Markos calls it.

Also want my squats to catch up, because they are far behind my deads at the moment. But soon I'll return to the deadlift 1RMs and I'll definitely give 220 a crack! Tough ask for a tall skinny 80kg not going to PTC :P

I used to have just a generic diary and would scribble shit down in there, but now I just use a very basic notepad app on my phone. Only really need like 2 weeks of notes at any time to skim back through anyway.

Lunges are the worst torture known to man. I'm properly struggling to stand...squats never did this to me!

They just have this ability to extend the set beyond physical pain and it becomes all about how much you can put up with mentally.

Yea walking lunges say.....for a about 20-30 meters with lots of weight on a barbell on your back is the worst kind of pain especially after the half way mark where you just want to give up because of the intense burn. Not to mention the nice cardio workout that comes with it. I do them twice a week and have developed excellent shape as a result. Squats had sliced my lower back in two so utter fail for me :(

Eating peanut butter

This. lol. And incline leg press (plate loaded). Got up to 360kg for my working sets, so at least I wasn't being a bitch on the thing.

Looks like my ROM issue through my shoulders wasn't quite as bad as I thought, since it was pointed out I had the bar way too low anyway haha...so now that I'm resting it in a more appropriate position as well as stretching my chest/shoulders/etc beforehand, I can do barbell squats again.....my traps are f**king obliterated though, not used to having weight resting on them >.< will get used to that though.

Best part is 100kg feels like nothing! (inb4 that asshat Markos pointing out 100kg IS nothing :P). Should be back up to a more appropriate weight in no time. Will increase 5-10kg for the next couple of sessions, then 2.5kg every session without fail from then on.

Markos, I remember you saying not long ago that nothing you see amazes you anymore. I'm curious: what's the most impressive or amazing thing you've ever seen with regard to lifting?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...