Jump to content
SAU Community

Recommended Posts

I'm over jap cars! When you go prestige you will never go back.

Try it one day you will know what I mean - Then realise you use to be a hoon - Then realise why everyone hates them and join them hating them. :-)

Jap cars were good 5 years ago when everyone left you alone but now everyone is against them.

Go prestige - No defects - No EPA's - Save on Petrol. And all you need to do is put a set of sexy wheels on.

Wholeheartley agreed.

I don't own any prestige car at the moment but I am hoping to buy a 2006+ Bmw series 3 by end of this year fingers crossed. For the amount I'm going to spend, i could perhaps own a evo x as i believe jap cars do have the sheer grunt and power, no one can dispute that but end of the day, they severely lack in class and looks.

I am beginning to notice more Audi, Merc and Bmw's in Melbourne's inner cbd and it's surrounding vicinity.. This city is slowly but surely transforming into a high class city, after all, it is Australias fashion capital.

My friends live in areas where every 2nd car parked in the drive way is a German built car and when i go out for coffees or dinners in these areas, i do feel like a major hoon in my Skyline even though my car is fairly moderately modified.

I think the Bmw's new 3 series look great with its smooth curves.

bmw-3er-silver-exterior.jpg

Edited by Barbarian
  • Replies 213
  • Created
  • Last Reply

Top Posters In This Topic

Driving a jap car around the more affluent suburbs full of German cars is great because there aren't anywhere near the amount of police around to hassle you as there are compared to suburbs where most the streets are scorched with burnt rubber.

That is except for anywhere around Chapel Street and Dandenong road

I am beginning to notice more Audi, Merc and Bmw's in Melbourne's inner cbd and it's surrounding vicinity.. This city is slowly but surely transforming into a high class city, after all, it is Australias fashion capital.

My friends live in areas where every 2nd car parked in the drive way is a German built car and when i go out for coffees or dinners in these areas, i do feel like a major hoon in my Skyline even though my car is fairly moderately modified.

What model are you going to be going for in the 3 series?

Correct me if i'm wrong but top spec (before m3) is the 335i (twin turbo 6cylinder). These do come in sedan form aswell correct?

Whatever you buy just make sure it's black :P

Yes I will give you the fact that Euro cars are prestige etc.However thats about it.I been behind the wheel of a few of them and honestly they are just ordinary cars that are ridiculously overpriced.Sure they may be a little quieter than most cars.And as far as build quality.they went down the toilet years ago.Ask anybody who ever works on one-They are just as big a shitheap as any falcadore.As far as I am told most of the mercs get their parts from Korea.I used to work in an unnamed company that had 50 Merc Sprinter vans...Every one of them blew gearboxes before hitting 100000 km..! ( $15000+ for the tiptronic auto )Then the diesel fuel injection systems started shitting themselves as well as computer glitches that wont allow it to go out of nuetral, doors that dont shut properly. I think VW is the best quality car in Germany right now...At least they are reliable

Im not over Japanese cars, but I am on a "break" from them, after nothing but turbo cars for the past 13 years its kinda nice to be driving a N/A v8 for a change. My Xr6t changed my mind on the whole japcar scene, I really dont go 'driving' much at all these days, most of what i seem to do is boring stuff to & from work etc....

Must be getting old! :P

Who else is feeling the same symptoms?

They just don't seem to have that "classy" or "elegant" touch in them, no matter what car or what brand, it's still a Jap car end of the day.

When driving around in Melbourne's higher class suburbia, you feel like a foreigner in your Jap vehicle.

sounds like you're trying to ' keep up with the jones's.' does it really matter what other people think about what car you drive.

if you drive an modified import you're pigeon holed as a hoon, if you drive a prestige car you pigeon holed as a snob.

personally i think prestige cars are rediculously overpriced and a complete wank, where you often pay >60K for something with a 2.5 litre engine, a hole bunch of electronic gadgets that break soon after the warranty runs out, and a brand name that's supposed to say 'look at me i'm successful'

maybe i just feel that way cause i work in 'upper class' mosman (sydney), and serve alot of customers owning poodles, driving bmw's/mercedes with superiority complexes

not trying to be rude, maybe i'm reading it wrong, i don't know, and that you meant you're in the market for a car that has a nicer interior and that looks more civilised than an evo etc??

lol as if a run of the mill predominantly junior marketing intern owned 3 series beemer is a sign of luxury. that's like assuming sipping cheap champagne in copious amounts at melbourne cup day can turn you from a skank to a lady.

down the track i'd be definitly considering a higher class euro car with some balls and hopefully be in the position to keep the liner as the fun weekender. i just want to drive a pimped out audi merc beamer or bentleigh's like all those rappper's do before lights out.

Ummm the Quality?

Its just like saying what can you get in a Skyline that you can't get in a Holden in the same price range?

your comparing lemon's with mango's

wat quality?

2 of my mates bought a 318i and a holden statesmen of the same year from the same dealer. the bimmer's broken down 3 - 4 times already and cost about 3 grand to fix. the stato's runnin like brand new. not saying holdens are better or that i'd ever choose a holden over a euro but yeah...

quality my arse, you think all mercs are bulletproof just coz they're mercs? they're made in mexico ffs

just my opinon but if i was to ever go euro i'd get somethin from the $100K+ range and from italy but since i dont have that sorta money ima stick to what i can afford lol

My friends live in areas where every 2nd car parked in the drive way is a German built car and when i go out for coffees or dinners in these areas, i do feel like a major hoon in my Skyline even though my car is fairly moderately modified.

bmw-3er-silver-exterior.jpg

I live next to the city. I drive an r34. The cars in my apartment carpark are, Porsche GT3, Porsche 911, bmw M6, bmw 3 series, 5 series, 7 series X5s, mercs e class, s class, you'll prob end up a millionaire if there's a grand theft auto :blink:. Anyway, I don't feel anything at all. We drive pass each other looking at each other's cars with a smile in our face.

I'm still young, not even mid 20s yet, i feel that driving an import at our age is perfectly fine. However, when i reach my late 20s, i'll be planning to get a euro car BUT still keeping an import as a toy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...