Jump to content
SAU Community

Recommended Posts

Spotted OH SNAP down the bay today.

Also black Celsior with plates:

CNT

ALNK

I don't get it :wave:

EDIT: That was the back, now I put it as CNTALNK I see Centrelink, I get it now.

Edited by Thomasino
ferrari 599 in north adelaide at about 8pm, f**k, seriously good looking car.

i see your ferrari 599 and raise you what im going to call (even though its not) a ferrari 430 on mcintyre, way cooler looking than the 599 im my opinion, although i believe the 599 has more gusto v12

looked like this but the 1 without the round taillights

http://www.ssip.net/upload/ferrari-f355-be...a-side-1_64.jpg

Edited by Inline 6
i see your ferrari 599 and raise you what im going to call (even though its not) a ferrari 430 on mcintyre, way cooler looking than the 599 im my opinion, although i believe the 599 has more gusto v12

your prob thinking of the Ferrari Testarossa. i see one of them around the golden grove area all the time. its one hell of a nice car.

i see your ferrari 599 and raise you what im going to call (even though its not) a ferrari 430 on mcintyre, way cooler looking than the 599 im my opinion, although i believe the 599 has more gusto v12

looked like this but the 1 without the round taillights

http://www.ssip.net/upload/ferrari-f355-be...a-side-1_64.jpg

I Get to see an F430 everyday parked in my neighbours garage... they are stuck up tosser ferrari's :cool: If I was rich atleast I would have taste and buy something cool like a Testarossa :D

Today I spotted a Silver R34 GTR Vspec II in a carpark by chinatown.... I think its plates plates were VSPEC II .. or something along those lines... there were a couple of R33 GTST's in the carpark aswell but looked pretty stock.

I Get to see an F430 everyday parked in my neighbours garage... they are stuck up tosser ferrari's :cool: If I was rich atleast I would have taste and buy something cool like a Testarossa :D

Testarossa cool? have you driven one ?, I drove my mates fully tricked out Konig twin turbo black model in aspen colorado for a month, looked really hot, but unstable with that much power(close to 900 dyno'd HP at sea level). and touchy engine didnt like a good flogging at high altitude, , plus being tall you dont fit for shit. gear shift is behind my kneee when i drive it.

not a fun car to drive ????, scrapes on every driveway. but at nearly $500,000 US invested in it, it does pull chicks like a money magnet..lol

its a look at me Im a WANKER car, but for a driver give me a GTR, Austin martin, GT3 or something like that.

his car must be one of the nicest Testarossa in the world, PS. he is very very rich and single for all you materialistic girls out there, 35 yrs old.lives in many locations worldwide.

sorry this isnt the dribble thread...lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...