Jump to content
SAU Community

Recommended Posts

Watch a bit of the Bathurst 12 hour race, quite a good mix, Evos, STIs, Holdens Mazdas and BMW. Have to say, there are days when Evos really really piss me off because it's so bullshit fast around the corners but it's good to see them owning the holdens and european cars.

Where are all the GTRs????

Link to comment
https://www.sau.com.au/forums/topic/206307-bathurst-12-hour-race/
Share on other sites

omg did you see that Mazda MPS.. the blue Thrifty one.. loose it and flip?!?!! I counted 9 times, and the guy was just a bit unsteady on his feet but was fine!

The whole engine fell out! lol

< owch

Saw that the other day on some show. The last lap of his last race and that happened to him!! They said he spent 3 hours totally blind lying in hospital...what a way to end ya career!!!!

GTRs are in front of the evos but not invited because they have to be less than 5 years old :D

here's a pic from oran park last year :)

chop_evo.jpg

the thrifty mazda was racing that day too, but he did better than he did at bathurst. ouch.

this was run a few weeks back and they showed the crash on sports tonight that night.

I thought it was funny a Satria GTi did more laps than a GT-P. Cubes aint everything.

you obviously weren't paying attention to the fact that the GT-P spent about an hour in the pits after the front seal on the diff let go and dumped all the oil out.

this was run a few weeks back and they showed the crash on sports tonight that night.

you obviously weren't paying attention to the fact that the GT-P spent about an hour in the pits after the front seal on the diff let go and dumped all the oil out.

Just thought it was funny as i work in a dealership with both ford and proton. normally all the ford guys hang shit on the protons all day. Was good to see it the other way round for once. Falcon diffs are crap anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...