Jump to content
SAU Community

Recommended Posts

hey guys i got an r33 gts25 rb25de. usually to a full tank ide get an easy 450-500km.

pretty much used the whole tank today its sitting on the bottom bar and ive only done 299km.

any ideas as what could cause such bad fuel economy??

ive checked exhaust for leaks but there isnt any. the car has had no loss of power so ??? i dunno what it could be.

and yes ive tried the search but couldnt find anything

Link to comment
https://www.sau.com.au/forums/topic/208426-fuel-consumption/
Share on other sites

and yes ive tried the search but couldnt find anything

really?

http://www.skylinesaustralia.com/forums/Pr...uel+consumption

http://www.skylinesaustralia.com/forums/o2...uel+consumption

o2 sensor, service the car, maintenance, etc.

troubleshoot what you've changed recently. ambient temp can also have an effect.

thanks eug for that.

my driving has not changed, i havent been driving it hard at all.

ill clean the afm. and check the o2 sensors. it shouldnt be to hard to change the o2 sensor myself shouldnt it?

and yes im useless with the search..

if you do a search there is a cazillion topics on o2 sensors

basically they are meant to be changed every 40 thousand kms so its a good idea to get a new one

when i got a new one about 5 thousand kms ago my fuel went from 450 kms to a tank to about 530 kms a tank so its well worth it.

  • 2 weeks later...

first thing is to check for fuel leaks, a clamp may have come loose somewhere in the engine bay so just check them to be safe. also check your coolant temperature sender for surface corrosion on the connector... if the ecu doesn't get a good signal from the coolant temp sender it may think the car is running cold and will richen up the AFR's. you can clean the CTS with a nail file, just need to remove any surface corrosion so that the sensor and loom connector have nice clean metal.

if O2 sensors and CTS checks out, check your fuel pressure regulator and also do an intake pressure test to see if you've got any vacuum leaks.

also try and get your car on consult or datascan to check for error codes.

After you've gone through all that, get your injectors taken out and properly cleaned and inspected ( condition & spray pattern ). Chances are, if you've done over 100,000Km the spray pattern and operation of your injectors will be less than optimal.

Just my 2 cents......

have you tested your o2's? you can do it using a voltmeter or using consult/datascan. you just need to make sure they're nice and responsive and that the voltage output should sweep from low to high about once a second. datascan or consult is easiest coz it will just display the voltage output for you. just make sure your car is at operating temp and you'll need to rev to about 2000rpm when you're measuring the voltages.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...