Jump to content
SAU Community

[group Buy] Acpt Carbon Fibre Tailshafts Any Model! $1400us


Recommended Posts

yeah i was dissapointed at the balance weight on the shaft also. In terms of the spacer we made up if it came with the correct parts, I wouldnt have a problem...

I really am over it, I don't want to be spending money going to a shop getting it balanced when it should come from the factory ready to go. Time and money... Don't want to be spending the next 3 months fitting and re-fitting the thing trying to get it right. Shouldnt have to.

I'll contact ACPT today, I expect nothing less than money back. I will happily ship this junk back to the states as long as they are paying.

Mick

  • Replies 717
  • Created
  • Last Reply

Top Posters In This Topic

Hey Andrew, not your fault mate.

ACPT have offered to ship the shaft back to the US at their cost, check the balancing etc, if it is out, refund me.

Truth is, I do want the shaft. I might try somewhere local and just lump the costs...

Mick

ACPT arent all that bad in the end, especially if you deal with Jim Leslie the boss...

Hope others are ok. Still waiting for ours to arrive - take 2...

Andrew its not your fault what has happened.

Anyone know what it would cost approx to balance the shaft in Oz...just want a ballpark figure

Inline with GB rules about having a start & end date - this is now closed.

http://www.skylinesaustralia.com/forums/Th...Gro-t81129.html

SAU is clamping down on these GB's that never occur, never end, and so on.

PM me if you have a problem. However, before you PM me think about this.

A group buy, is a group of people buying the product together to lower the price.

Buying single units here and there is not what constitutes a GROUP BUY

Thanks

opened again guys! keep the discussion going here.

we'll wait till everyone has their shafts going untill closure of this. (or ones like me who dont think they will see the light anytime soon will keep intouch)

Cheers

I think my shaft is one of those unbalanced shafts! :blush:

I have a vibration in every gear.... above 70km/h you can really feel it

I will be pulling it back out and fitting the stock shaft. Not impressed!

I think my shaft is one of those unbalanced shafts! :blush:

I have a vibration in every gear.... above 70km/h you can really feel it

I will be pulling it back out and fitting the stock shaft. Not impressed!

Where u at might be able 2 do yours with mine?

Yeah in the same boat & yeah not F%$#*&^% happy.(Not with U Angus)

For a reputible company they have issues in the balancing dept.(or they thought stitch those Ausies up)

Tested mine & have the same problem vib starts at 90klm/h & by 120klm/h decided enough was enough this needs a rebalance FFS.

Have emailed James to let him know of my problem,but with them so far away wtf can he really do.Maybe cost me $60 for a balance but in the end be satisfied & no vibration.Be more than $60 to send it back to the GREAT USA to get balanced when i can do it here for F^$# all.

And again not having a shot a u Angus ,in no way is this your fault.

Edited by YLD-CHLD
Where u at might be able 2 do yours with mine?

Yeah in the same boat & yeah not F%$#*&^% happy.(Not with U Angus)

For a reputible company they have issues in the balancing dept.(or they thought stitch those Ausies up)

Tested mine & have the same problem vib starts at 90klm/h & by 120klm/h decided enough was enough this needs a rebalance FFS.

Have emailed James to let him know of my problem,but with them so far away wtf can he really do.Maybe cost me $60 for a balance but in the end be satisfied & no vibration.Be more than $60 to send it back to the GREAT USA to get balanced when i can do it here for F^$# all.

And again not having a shot a u Angus ,in no way is this your fault.

Mate im at Bankstown. Thats not a bad idea. I really want to have this shaft but it need to be fixed up. Ill be keen to meet up and send them both in to get balanced... where ever that is.

Sorry to hear about all this Andrew, what a clusterfcuk!

I was considering buying one of these shortly as well but will be holding off on that for the time being :(

Seeing that ACPT make the shafts for mines.... I wonder if they have any issues like this? Or was it just that they thought we are a pack of Aussies over the other side of the world and wont give a stuff?

On the upside i did notice a bit of response gained :banana:

Clearly ACPT farked up our order then rushed a heap through to get us to shut up. They're not expecting any of us will be willing to send it back to have it balanced after taking so long to get them, so they get what they want; our money and never hearing from us again. It's not like they expect repeat customers so who cares what a few Aussies think.

Dam shame this group buy went sour.

On the bright side considering SAU is one of the largest skyline forums in the world I seriously doubt that ACPT will ever sell another tail shaft to a Skyline owner in Australia again. Thats a whole market they have just succeeded in losing themselves.

If an aussie company pulled that crap and didnt fix it they'd find a tail shaft thrown through the front windows of their show room or the windscreen of their demo car. Companies that pull this kind of crap deserve to go broke.

sorry to hear this happen to you guys. I was planning on putting my name down for this but seeing this happen makes me think thank fcuk i didnt. if it helps maybe everyone who has been placed with a dodgy tailshaft should get together and mail the company on their complaints. power in numbers people even if only a small group. bad publicity isnt any good to any business. word easily gets out over the net.

http://www.acpt.com/index.html

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...