Jump to content
SAU Community

[group Buy] Acpt Carbon Fibre Tailshafts Any Model! $1400us

Angus Smart

By Angus Smart,
in Group Buys

 Share

Recommended Posts

Granthem Mentor

Granthem

Posted
Posted

Wow, what a read.

Fingers crossed all this gets sorted. Bad luck for the thread starter, he will probably never attempt such a thing again. However, organising a group buy is a whole lot of effort on one persons shoulders for no gain personally, so chin up hopefully this shamozzle wont put you off them forever :thumbsup:

  • Replies 717
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Angus Smart Grand Master

Angus Smart

Posted
  • Author
Posted
New shaft is on its way currently, will let you all know of the outcome. Better be balanced properly...

sweet good news! glad you got your problems sorted, i think alot of us are still yet to try them? i should do it soon but i am going to take it to a balancing shop before i attempt to use the shaft considering the problems that have happened.

as for the last post.. your right! i feel bad for dragging everyone into this mess!! i thought a carbon shaft would be a good addition to my pile of parts.. wasnt i wrong!

elrodeo666 Mentor

elrodeo666

Posted
Posted

Yes but does it fit...is it balanced..

I'm too paranoid to take mine out of the box...tailshaft balance shops are as rare as hens teeth over here. Anyone i ask here just give me a stupid look and ask ,why did you buy an unbalanced shaft??

Andrew ..not your problem mate...reckon its pretty dodgy customer relations from ACPT, the been great on the emails but bloody slow as for delivery. At least its not as slow as an engine build, my engine still hasnt come back from maching but any day now..

Piggaz Grand Master

Piggaz

Posted
Posted

This week i'll be refitting my stock shaft to see if this vibration goes away. Part of me hopes it does..... Part of me hopes it doesnt. If it does another long cardboard box will be on ACPT's doorstep. :).

Piggaz Grand Master

Piggaz

Posted
Posted

Shaft is out. Stock shaft is in. Vibration gone. ACPT is getting their shaft back.

For the guys that have sent their back... how did you go about this? Who did you speak to? How much was postage?

Angus Smart Grand Master

Angus Smart

Posted
  • Author
Posted

shit this aint looking good, i'm not sure if anyone sent theirs back yet??

i'm going to bite the bullet when i have a bit of spare money and go get it balanced..

Piggaz Grand Master

Piggaz

Posted
Posted

Andrew. Are you going to get your balanced here in Australia? (If it is out... Hopefully it isnt). What happens if you get it balanced here and somehow it breaks in half. Will ACPT come to the party seeing that you modified their product? We shouldnt have to get these things balanced.

Food for thought :)

PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

My god, what a read! I feel so sorry for you guys and especially you Andrew, your a good bloke for keeping your head up, most people would have just given up. Hopefully this all gets sorted out, but damn, what a bunch of f***ing c***s is the US for pulling this shit. Fully agree that they are lucky they are not in Aus......

Edited by PM-R33
mitchy_ Grand Master

mitchy_

Posted
Posted
Andrew. Are you going to get your balanced here in Australia? (If it is out... Hopefully it isnt). What happens if you get it balanced here and somehow it breaks in half. Will ACPT come to the party seeing that you modified their product? We shouldnt have to get these things balanced.

Food for thought :)

perhaps just get it checked to see if it is out of balance or not..

Angus Smart Grand Master

Angus Smart

Posted
  • Author
Posted

theres a balancing shop round the corner from me in bankstown, when and if i ever get my motor back and installed i will take the shaft there once i have the car running. i want to do a before/after comparison

but this is problably a few months off now..

elrodeo666 Mentor

elrodeo666

Posted
Posted

Yeah I'm the same Andrew, just got my block done now head has been sent off for maching so gunna be at least 6 weeks and probably early may sometime befor it all goes into the car. Finding a tailshaft balancer is like a needle in a hay stack here.

Mr. Keets Grand Master

Mr. Keets

Posted
Posted

Well the light at the end of the tunnel seems to be the sun and not a locomotive. The Shaft spun up well and the dimensions are within spec but....

At the front, a ring had to be machined up to sit between the adaptor and the locator on the front of the shaft. The adaptor supplied didn't locate on the front of the shaft very well as it would have only been bolted on through the 4 nuts and bolts.

AdaptorFront.jpg

More nonsense on the rear. The adaptor supplied (right hand side) was machined up to locate on the centre of the tin plate on the end of the tail shaft. The adaptor that was machined locally (left hand side) locates using the outside of the shaft.

AdaptorRear.jpg

Now comes the good part. :wave:

elrodeo666 Mentor

elrodeo666

Posted
Posted

What's the good part Mr Keets??

How much did that all cost to be machined up???

I've got buckleys chance of getting it done here in ping pong land!

Mr. Keets Grand Master

Mr. Keets

Posted
Posted

^ Mark. The good part??? it's finished and the car drives. Cost, a lot less than it's going to cost you in Japan lol. Let me know if you need something machined mate

Well this is it guys... JOB DONE !!!11ty!!!

Run 60 = 430.5 pre shaft, original tune from the middle of last year

Run 63 = 428 Shaft installed...running fat

Run 67 = 433.9 Shaft installed...basic tune, probably more in it but this isn't for sheep stations.

It's hard to say if it feels different as I haven't driven the R for quite a while. But the comparison says it does. Was it worth it? lol. Personally I believe if you continue to pursue the small gains, especially the more cost effective ones :banana: , they add up to decent gains. Well that's the plan anyway

Discuss

post-a211429-keets-dyno1.jpg

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      HFM BM57 has a "bad" knee point, IIRC. It's not the same thing as the later R chassis MC.
    • Duncan
      Who has a Infiniti Q60, Q50 (V37)?

      By Duncan · Posted

      The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • MBS206
      Who has a Infiniti Q60, Q50 (V37)?

      By MBS206 · Posted

      Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
×
×
  • Create New...