Jump to content
SAU Community

Recommended Posts

r32 on corrigan rd or chandler rd. i forget which one. black with gtr stickers all over the shop, big one on the rear windscreen, on he sides, two on the back etc. only really caught a glimpse but i think it actually was a gtr. we get it dude

yeah i spotted that one today too. It needed a wash badly. I also spotted a silver R33 GTS4 on the next floor up. It had one of the cheapest and most awful looking kits i had ever seen

Edited by Swink33

Also spotted 2 very nice R33's at Holmesglen McDonalds last night at approx 12.45AM. One was white with rims, exhaust, kit. Looked really nice and was leaving as I arrived. Then as I was leaving a custom orange painted one went past. Also sounded nicely modified with custom plates

spotted SKYL1N in richmond tonight around 1am ish turning right onto bridge road. I was at the pub having a few after work...

Were you cruising with the white bmw in front of you? That Steve by any chance?

Hey, Been a while since been spotted. yeah was with Steve in the beema. ridiculous first car.

spotted htial at 3:20pm today turning onto westal road from heatherton road :P

Gahhh... ...Slow internet connection!!!... ...Would have posted before you... :P

Saw you zip right to get around that truck and then have to zig back in front of it to miss that little red car trying to turn right... ...and then zag back into the right lane...

Also saw another Silver 33 about an hour earlier on Springvale Rd near the rail crossing... ...Had a really low rear bar... ...and looked kinda like someone had gone to town with some sand paper on the boot lid where the GT-R badge would be if it was a GT-R...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...