Jump to content
SAU Community

Recommended Posts

Ah fair enough. Surprised I don't see you more often then. I go the opposite way every morning.

I start work at 7. Poor guy had to essentially drop me off n turn around n come get me again cuz I was still too sick to work. I'm usually on white street at 6 35

don't know the plates but saw the gold r33 with dished rims (dr33m) maybe not to sure and the r34 GTR with initial d stuff on it failing on the plates sorry both entering kfc/hungry jacks lower dandenong road

Daniel JDR33M and Linsey JDMCOP (R34 GTT)

silver r35 [r38???] on westall rd (heading towards centre rd) around 9:30pm tonight

black r34 gtt with factory aero kit turning left from centre rd to s'vale rd just a bit after. half your tail lights are out (semi-circles zzz) :P

Finally got to say hi to ya, krzysiu. Sorry I didn't cruise long work tomorrow :(. Seen your car a few times around here but usually in the daily.

Haha nice to talk to you mate. I was tripping balls when you said GTR. Knew they existed but didn't know there were any here! Very nice :D

Finally got to say hi to ya, krzysiu. Sorry I didn't cruise long work tomorrow :(. Seen your car a few times around here but usually in the daily.

Hey nice 32 4 door GT-R was awesome to finally see one, i was telling the boys in the car before you said it was a GT-R that it was a GT-R but they they discarded the comment cause it was a 4 door. As you can tell by now i have the other CR34M.... :) Nice to meet you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...