Jump to content
SAU Community

Recommended Posts

Want to win, buy new tyres. Want to have fun, show up and have fun...

Want to win = spend some coin, same as always.

My point was (is) that there are plenty of people out there who would want to run in the road car class on R compounds. I would suggest more people fall in that category than those wanting to run on road tyres in the street car class. Allowing R comps would both boost entries & improve the spectacle. But that is just my opinion. We never seem to have any issues in getting road registered car entries on R comps where I am from.

Rear engined 6cyl cars are disallowed if you read the rules so goodbye porsche

I did. Its just that the rules killed off Porsches in the same way the internet has killed sarcasm. I was being sarcastic. Not that it matters. :banana:

  • Replies 1.9k
  • Created
  • Last Reply

Top Posters In This Topic

yeah mate I am probably with you on that point. most guys I know running at the circuit use R comps even on mild road cars. and I reckon a set of decent R comps will probably cost me less and last longer on track that a really good set of road tyres (think of the price of some top level michelien or pirelli's).

but I guess it's one easy way to distinguish the classes.

on the upside my GTR on a set of crummy road tyres wont need decent brakes as tyre grip will be so minimal.

yeah mate I am probably with you on that point. most guys I know running at the circuit use R comps even on mild road cars. and I reckon a set of decent R comps will probably cost me less and last longer on track that a really good set of road tyres (think of the price of some top level michelien or pirelli's).

but I guess it's one easy way to distinguish the classes.

on the upside my GTR on a set of crummy road tyres wont need decent brakes as tyre grip will be so minimal.

I ran some sad roadies on a track in my GT-R once. Bashed the living hell out of the tread blocks.

Buffed tyres, anyone?

concerning the tire listings for Club class> just a heads up there is a listing for the Falken RT 215 but no RT 615 which has replaced the 215...

that being said, they aren't really a R rated tire... neither are the Federal 595RS

when is Superlap coming down to Mexico!

The good news is after talking to some people in the know with tyres ( thanks Andrew aka Snowman ) we have finalised the Tyre rules.

Clubsprint Class

"All vehicles entering the Superlap Clubsprint Class must run on Tyres with a UTQG rating higher than 100. Each entrant will have to advise us on their entry form which tyre they are going to use. If the tyres fitted to your vehicle have a UTQG rating under or equal to 100 you will be moved into the Open Class"

Open Class

"All vehicles entering the Superlap Open Class must run on R compund Semi Slick Tyres. The only semi slick tyres not to be used in Open Class are: Hoosier R6, Hoosier A6, Kumho Ecsta V710 & Avon Tech R-A"

Edited by Snowman
The good news is after talking to some people in the know with tyres ( thanks Andrew aka Snowman ) we have finalised the Tyre rules.

Haha - yep so if you don't like the tyre rules feel free to vent at me :teehee: But I'm pretty sure everyone will be happy with them now and there should be no real complaints. Same rules as we run in our comps and it works perfectly.

oh oh. I see lofty lurking in here. bad news for us all! bring the starlet dave... :)

The Starlet can stay at home but we now can pull those bloody restrictors out and have a real go

yeah baby!!!!!

just have to do a round at w/p as improved production first, (i dont own that o2L lap record yet) then the car will be changed over

dave loftus :teehee:

Hey Nathan are you going to post up a new approved tyre list?

All i could find on the cams website was stuff about 60% ASPECT RATIO INFORMATION

Groups Nb, Nc, Sa, Sb, Sc, 65% ASPECT RATIO INFORMATION GROUP Na?

are we the 60% ratio?

Why the rule banning Porsches from ClubSprint class ? Is the event going to be predominantly Japanese vehicles or are other Australian/Eurp marques encouraged to enter. I see some BMWs are in the mix

As for tyre rule, i can see a lot of ppl needing to upgrade to 18s to really get the lower profiles happening, as the tread can be buffed down. Big thing will be sidewall and from what i hjave seen on my 17s, you will probably get more out of some lower profile 18s?!!?!?!

But good to see something formal coming to club sprints. Be interesting if you get all the main cars from the main clubs from different states. Will see which clubs/marques have the quickest cars :teehee:

Hey Nathan are you going to post up a new approved tyre list?

All i could find on the cams website was stuff about 60% ASPECT RATIO INFORMATION

Groups Nb, Nc, Sa, Sb, Sc, 65% ASPECT RATIO INFORMATION GROUP Na?

are we the 60% ratio?

The Tyres are pretty open now. There are alot for you to choose from. On most websites you should be able to find the UTQG rating on each tyre. If you are unsure shoot me a pm as I have a list and should be able to let you know if it qualifies.

The requirements mentioned on the site are the final ones I asume??

Planed to enter mine in the open class but after reading the regs if I fit a few things back in I can go street.

The rules are not 100% yet as we are still waiting to hear back from cams. But when it comes to vehicle modifications they are pretty much set in concrete.

Cheers

-Nathan

Edited by Superlap Australia
hey dazza

you coming to gatton next week end?? will be good to catch mate

Hi Russ Yea mate I am coming up to gatton won't have my car there will be in getting the exhaust system made up finally. Matty has entered his car so I will just be coming along to make sure everything goes smoothly with it an spectating will be good to catch up for a drink with you. Just sent off my eoi for super lap so I will have to pull my finger out and get my car finnished off. Will probably see you at the track next week Mark said you guys were coming along so I will catch up with you there mate.

damn i built my car specifically for these kinds of events but i got a 30/25. I think this has actually worked against me. My car is 100% a daily driven street legal car but the engine puts me into the open class which is full of hardcore track vehicles. The fact i need to use my car as a daily driver and its completely financed by one 22 year old means i'll be completely out of place competing in the same category.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...