Jump to content
SAU Community

Recommended Posts

You didn't have to pull those 4 bolts out, you just need to remove the cir-clip holding the shifter in at the bottom where it pivots, and she will slide right out.

I dunno where you got the idea from but whats wrong with filling it from the fill plug on the gear box? If you can get your hands on a little hydraulic pump just shove it in the new oil bottle and pump away until she is full.

Hope you know how much oil to put in, goodluck. :worship:

either spend $20 on the little pump bottle or $20 on a pair of circlip pliers. I like doing it from the top. It's clean and easy. You always end up with half an arm covered in gear oil if you do it from under the car

+1 for filling through the shifter hole.

I use a pair of needle nose plyers with the points bent inwards as circlip plyars for all nissans boxes... its lasted me 5 years so far and counting :worship:

provided you know exactly how much to fill the box. you cant go wrong!

I haven't had a good enough look at my GTR but why does the stick go into the transfer case and not the gearbox? Doesn't the transfer case literally transfer drive to the front wheels? From what I can see the transfer case hangs off the driver's side of the gearbox and the stick is perfectly above the gearbox itself like any other rwd car. Just wondering the reasoning?

Cheers,

Matt

i hope you have a 2wd. in 4wd the gear stick goes into the transfer case not gearbox

hey you don't have to beleive me but maybe you should take a closer look. the gear stick goes into the xfer case and actuates the gearbox via a linkage. the transfer case is bolted to the back not the side of the gearbox

hey you don't have to beleive me but maybe you should take a closer look. the gear stick goes into the xfer case and actuates the gearbox via a linkage. the transfer case is bolted to the back not the side of the gearbox

^believe this guy, trust me, i found out the hard way.

Sorry didn't mean to be rude, but cool thanks for that. Was just wondering the mechanics of it all, this is the same for all GTRs? Also, does that mean you can fill the transfer case from the stick?

hey you don't have to beleive me but maybe you should take a closer look. the gear stick goes into the xfer case and actuates the gearbox via a linkage. the transfer case is bolted to the back not the side of the gearbox

sorry its been a long week. the xfer case bolts onto the rear of the gearbox, and yes you can fill the xfer case through the shifter on a 4wd. bascially the xfer case has a main shaft to the rear wheels and another for the fromt shaft linked by a big chain.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Holy shit... wow!!! I totally missed this
    • One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...