Jump to content
SAU Community

Recommended Posts

ok here goes, mechanic added a thing that adds on to the air sensor (i think it is) when it was on we turned the car on and it obviously started, anyway when we revved it a bit the sensor wasnt sensing the air ratio and the car started to make blow off noises from the air filter and was occasionally blowing some air out of the BOV (thank god we didnt test drive it) anyway we turned the car off and disconnected it and put it all back to how it was before he touched it...

now the F*N thing wont start, it cranks but wont kick over at all, we even pushed it down a hill it wouldnt even jump start...

ok now heres my question, is there some sort of relay or fuse the car could have blown? is it the computer thats fried? any info i would appreciate, it only happened yesterday and shes only been in the driveway for a day and its sending me insane!!!!!!!!!

PLEASE HELP ME!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/216277-help-me/
Share on other sites

1) find a new mechanic

2) dont buy cheap ebay 15BHP hacks - they are all a load of shit

3) check the wiring in the engine bay, the hack would have been applied to the AFM signal wire, check it

the afm signal could be shorting out, unplug it, when its unplugged the RPM should cap out at 2500rpm but it should start and idle ok with the AFM unplugged

check the water temp sensor, if he was fidding with that and fried something the car wont start with a damaged water temp sensor, again just unplug and see if it starts

the water temp sensor is on the radiator pipe going towards the engine, theres two plugs, you can unplug both to test it easily

4) check all other fuses and sensors that you can see, fuses are in the engine bay, in the boot, and on the right side of the steering column

5) run stock ecu diag

6) take it to another work shop if all else fails

Link to comment
https://www.sau.com.au/forums/topic/216277-help-me/#findComment-3821116
Share on other sites

sometimes things are too good to be true aye.

did you give the thing for your mech to fit or did he suggest it? I know when my afm is unplugged the car would start once but after that it won't turn over no matter how many times. they say it should be able to turn over but idle low like paul said but for mine it wont turn over at all. Maybe you killed your afm?

Link to comment
https://www.sau.com.au/forums/topic/216277-help-me/#findComment-3821392
Share on other sites

my best guess- the 'chip tuning' company flash tuned the ECU memory chip to give more fuel into the mix, and now your plugs are massively fouled

change/clean the plugs, change back to standard ECU calibration, and get back to us....

Link to comment
https://www.sau.com.au/forums/topic/216277-help-me/#findComment-3821519
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...