Jump to content
SAU Community

Recommended Posts

Just had my exhaust completed by adding 3" dump and front pipes to the existing 3" hi-flow cat and 3" cat-back system.

Problem now is that the acceleration *feels* lazy, especially 2nd gear. Even the dodgy stock boost gauge is peaking a bit lower than what it was. Granted, I haven't got any actual data to show for a loss in power, but its a feeling that I'm getting which is enough for me. :D

Its not a flat-patch at a certain rev-range, it simply feels that the car is slower all the way through.

Anyone else had this sort of experience?

On the plus side, I can hear the turbo spooling up more now, which I like but that doesn't make up for when I'm getting smaller in someone else's rear-view mirror.

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/
Share on other sites

I don't have a boost controller so I can only assume I'm running stock boost. That being said, the stock gauge reckons its running at about 9psi (needle *was* right on that middle mark between 0 and +7, now its just under it).

I wondered if the ECU wasn't used to the breathing space but I haven't done anything about that (no piggybacker or reset or anything logical) and I'm pretty certain the O2 sensor is ok. It will be old, but ok and I'm basing that on the fact that the car was doing well before the new pipes were put it. Although, I'm now wondering if the mechanic perhaps had a go at cleaning the o2 sensor. Would that have an affect on the ECU at first, particularly if it was really grubby before?

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3836673
Share on other sites

I put FMIC, Pod, Full exhaust and my car went worse than before the mods. once I got my turbo Hiflowed and tuned to suit all the mods...Its a Rocket.

Stock ECU is good for the STOCK setup once you change something the tune needs to change with it. do all the mods you wanna do then get a ECU of somesort either stand alone or piggyback and get it tuned properly.

My car has gone from using 13.5 Litres per 100 to 8.8 Lph, not to mention bucket loads more power on the loud pedal.

and still makes full boost by 3000rpm.

Dave

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3836741
Share on other sites

I was hoping to get an ECU remap with Dr Drift once I got my boost controller and FMIC installed. Unfortunately I probably won't be able to get the FMIC put in for a while.

What would people recommend so far as an interim tuning goes? Is it worth it, or even possible (without any PFC/SAFC etc), to get some sort of tuning done prior to the FMIC?

Maybe I should resolve myself to biting either one of those bullets: "zero-power" or "empty-wallet" until a proper ECU solution is found.

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3836855
Share on other sites

If the computer is the problem why dont you just put the stock dump/front pipe back on then save for the computer then get it all done. Have you checked to make sure it was all installed properly? or did u tell your mechanic the situation?

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3837129
Share on other sites

Yeah as others have said.

I'd get it on a dyno.

Check the AFR's, fuel pressure, boost pressure and other basic things while there and get an idea of where the car it at.

Then workout what area it is thats needing the attention

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3838232
Share on other sites

  • 2 weeks later...

what? thats impossible, then why go for an extra dump pipe if you ain't going to tune your car?

What you guys are saying goes against the theory a turbo back gives more power than a cat back (with no tune).

Does this power loss theory with an extra dump pipe also apply to GTT R34's??????????????????

Edited by 10MinuteCar
Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3866199
Share on other sites

Does this power loss theory with an extra dump pipe also apply to GTT R34's??????????????????

Its even worse on a 34gtt, i dynod one stock, then he came back with a full turbo back 3.5in, and front mount. It gained 5rwkw up top and lost about 30rwkw everywhere else. Put a pfc on it and got it all back and heaps more.

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3866266
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Is anyone running these axles? R32, R33, R34 GTR front Axles. shafts itself rated 950hp. Suit all RB26 engines Croydon, Melbourne, Victoria Would be nice to pay half the cost of Driveshaft Shop Axles. I'm building an AWD S13 Coupe that is very low ride height (high cv angle) compared to stock R32. Has an RB30 with appx 600whp. Just looking for feedback. Thanks, Josh- https://www.instagram.com/feng_shui_garage/
    • Been a long time since r31 got some love, my brother dropped a shitbox ls1 crapadore in my lap to fix up.  Put a wiper motor in as the flooded one was no longer alive.  got windscreen wipers now. Time to clean respray and install back in the titanic  IMG_0505.mov
    • Nah its a server spammer thing  Although, now that I manually approve all the accounts I can probably loosen up some of the restrictions.  
    • Thread bump, again! Although, no bad news this time. Posting for the sake of possible root cause. Basically, I rebuilt it (mostly stock), installed Haltech + sensors, had it running fine on new ECU.  Still not really understanding why it cracked pistons last time. Got to tuners, and while checking timing, noticed +-10deg of timing scatter while revving. Changed CAS, and it was rock solid. While not definitive, can't imagine seeing 20+ psi with that amount of scatter would be a good thing. Also glad I found something.   Bit more of a run down; Carried out a stock rebuild, a set of stock pistons, out of a spare bottom end. Everything stock apart from head studs and oil restrictors. (so I can pretend I didn't let the Nissan out, ha.) Armed with the measuring gear and FSM, set about doing overhaul. Oil restrictors as per oil control thread for a RB25, stock oil pump, drifting. Head drain/vent from rear of head, to passenger side of sump above oil level. Two dash 10 vent lines from drivers side of sump (unused atm) Hi octane style cam cover breather kit Splash covers over last 2 cam caps. Both breather lines from cam covers to vented to atmosphere catch can, not plumbed back into sump (wanted to see what it was actually breathing). Got it run in (did about a 1000km) no to low boost scenario, As I had questions over old ECU setup. Installed haltech +sensors for flex Retune on E85 (finding CAS Issue along the way), made 300rwkw at 20psi, out of wastegate. Did a drift day the next day (yes, it was a big weekend!) and was checking catch can throughout the day, ZERO blowby. I mean nothing. Lines from cam covers are not even wet. Done a bunch of street driving, spirited and catch can is still dry. Early days I guess, but pretty happy so far. Also now run 10w60, up from the 10w40 that I used to run. Oil pressure is significantly better, especially when hot (as you would expect)      
×
×
  • Create New...