Jump to content
SAU Community

Recommended Posts

I'd like to announce the following SAU-Vic Motorsport Championship Class sponsors for 2008.

Please support our sponsors.

Kamikaze Motors

header-left.jpg

34-42, Rooks Road, Nunawading, Vic 3131

Phone: +61 3 9872 6699

Fax: +61 3 9872 6655

[email protected]

http://www.kamikazemotors.com

Sponsoring Class B and Class E

Kamikaze Motors Cup - Class B - Standard GTR

Kamikaze Motors Cup - Class E - AWD 2.5 litre + Under

Racepace Motorsport

rpm2s.jpg

9/6 Holloway Drive, Bayswater

Ph: (03) 9762 9421

http://www.racepacemotorsport.com/

Sponsoring Class A and Class D

Racepace Cup - Class A - Modified GTR

Racepace Cup - Class D - Standard RWD

RE Customs

recustoms.jpg

16 Yiannis Court, Springvale 3171

Tel: 61 (03) 9548 3414

Fax: 61 (03) 9548 4727

[email protected]

http://www.recustoms.com.au/

Sponsoring Class C and Class F

RE Customs Cup - Class C - Modified RWD

RE Customs Cup - Class F - Pre-1989 Vehicles

Micolour - Custom Refinishing

micoloursml1.jpg

7 Dissik St Cheltenham 3192

(03) 9555 8011

Sponsoring DECA Series

Micolour SAU-Vic DECA Motorkhana

Our trophies at the end of the Championship will be something like this.

Racepace Cup - Class A - Modified GTR

Kamikaze Motors Cup - Class B - Standard GTR

RE Customs Cup - Class C - Modified RWD

Racepace Cup - Class D - Standard RWD

Kamikaze Motors Cup - Class E - AWD 2.5 litre + Under

RE Customs Cup - Class F - Pre-1989 Vehicles

Micolour SAU-Vic DECA Motorkhana Series

Micolour SAU-Vic DECA Masters

Is Mick(think thats his name) from Micolour on here?

Heard he used to own a datto, and mine needs some body work... bit hard to pop down there with no motor in there and my gf using my stag lol.

-Ryan

Nice work

Need to win me that RE Customs Cup...

Ohh I better start entering some rounds LOL. I haven't done a WRX round this year yet... Stupid car issue made me miss PI.

I'm down for Sandown. Brisby? Newton? and where the f**k is DANE?

a little birdy tells me Ray might be dusting off the wide body s15. Bring the noise :)

bringit.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...