Jump to content
SAU Community

Recommended Posts

i was wondering if anyone could tell me how can i minimise this. only happens when im climbing hills at low revs.

alsogoing in for a dyno soon i was wondering is there a big difference between using z32 AFM compared to standard, is it just easier to tune using z32 or

do you get more power from it?

Link to comment
https://www.sau.com.au/forums/topic/221665-turbo-chuffing/
Share on other sites

when you say chuffing? do you mean compressor surge? turbo may be too small for the motor. if you have an electronic boost controller, you may be able to bring the boost on later.

as for AFM's, its tuning resolution, air goes through the AFM, and voltage increases with more air going through, problem with the stock one is it reaches max voltage with not alot of air going through it, so when you start moving more air (with a GT30) the ECU wont know because the AFM tops out too early. clear as mud?

Link to comment
https://www.sau.com.au/forums/topic/221665-turbo-chuffing/#findComment-3908353
Share on other sites

i had compressor surge with a highflow turbo i had, and it would only surge when coming underload (* going up hills, just comin onto boost)

i found out that the wheels (wheels were from an isuzu truck) that were in the turbo were way too big for it, and was pushing air back through the afm, or something to that effect.

i have a gt30r, and only issue i had with it was idle cause the air coming from it was affecting afm, so the afm was just moved further away from the turbo and is now fine.

Link to comment
https://www.sau.com.au/forums/topic/221665-turbo-chuffing/#findComment-3908633
Share on other sites

i think the hks cast low mount manifolds with balance pipe would eliminate it

Balance pipe for a GTR, no balance pipe for a Gtst.

I opted for the 100mm intake with the reversion flutes for my GT3076 aka Gt30r, just in case, to be sure, to be sure [and I have the Hks cast low mount and hi temp coated + extrude honed]. I have nil problems with it, but I am running with Tomei 256/8.5's so it will be just a bit different to std there as well.

You'll need a Z32 with the Gt30r, std will not give enough.

Link to comment
https://www.sau.com.au/forums/topic/221665-turbo-chuffing/#findComment-3909060
Share on other sites

lol a GT30R frame being too small for the motor, what a load of rubbish. It has nothing to do with that at all.

R33747 - When you say you don’t have a Z32 on there now, what is the state of the tune?

Fact you don’t have a Z32 makes me think your running a half-done setup as a GT30 is going to give you 270rwkw+…

A stocker AFM wont even come close

Now, the below is assuming you've setup the car and tuned it correctly etc, which I don’t think you have.

The GT30R is most likely the 600hp variant most likely...

They have a compressor wheel that’s classed as oversize... so at low RPM its going to surge, mine did just a little around 2000rpm.

Not a lot you can do unless you wanna start playing around with things.

The easiest way is to get the smaller 500hp wheel in the front, fixes all the problems and the car will be more responsive and virtually make the same peak power.

Link to comment
https://www.sau.com.au/forums/topic/221665-turbo-chuffing/#findComment-3910941
Share on other sites

i had Z32 AFM on the car when i had the power fc but when i got an EPA i put the stock ecu back in but the car wouldnt run properly with the Z32. i was just wondering if i could get away with it ( running stock AFM ) because its a hassle changing it. Also what kind of boost would you consider as safe when going for a dyno tune. Ive blown 1 motor and i dont wat to did it again.. I was thinking around 1 Bar. What are peoples thoughts thanks or experiences?

Link to comment
https://www.sau.com.au/forums/topic/221665-turbo-chuffing/#findComment-3915351
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...