Jump to content
SAU Community

Recommended Posts

I'm with you! Had a look at my BCM but I'm stuffed if I can find a BCM code on it........

Any ideas????

Or if I just send every number on it to Nissan Japan will they figure out the rest?

Thanks

Mark

I can't see the serial number on it. It's got everything else including the part number. Maybe it's under the sticker or on another sticker somewhere. It's a 5 character combination of digits and letters or just digits.

Tom

Well - I just heard back from Nissan Japan. Even though they couldn't help me their customer service is impressive!

"Thank you for your email dated November 12, 2008, concerning your Nissan Skyline. First of all, we appreciate your patronage of our products.

With regard to your inquiry, we regret to inform you that there is no BCM number in the photo you sent to us, and that vehicles manufactured after 2001 have no BCM label on them.

In that case, the only way to get PIN code is to read the BCM code by “CONSULT” that Nissan dealers have. Please note that the “CONSULT”

available in Australia may not be able to read the BCM code since your Skyline is a Japanese specification model.

Your understanding would be much appreciated."

Hmmm. Most here have said that Nissan dealers here can't help much. Am I destined to have one key forever? Any ideas?

Thanks

Mark

The good new for me is, it's only $150 to get the key made and programmed. That's the normal key without the buttons to open/close the door and the boot. But I still have another problem, When I insert the key to start my car, I have a device I need to push for 2 sec before I get full batt power, then I can step on the clutch before I can start her up. So do I need a aftermarket alarm install and throw out the button thing?

post-53067-1227051759_thumb.jpg

I got around to having a look @ my kick panel today and took a pic

Lucky for me my numbers and sticker look almost the same as FlyingEL

Tom could you please check out the picture I have attached and let me know if you can work the same magic you did for FlyingEL

Cheers

Stuart

post-9102-1227584917_thumb.jpg

I got around to having a look @ my kick panel today and took a pic

Lucky for me my numbers and sticker look almost the same as FlyingEL

Tom could you please check out the picture I have attached and let me know if you can work the same magic you did for FlyingEL

Cheers

Stuart

I've PMed you your PIN. Let us know when you get your new key programmed.

Cheers,

Tom

no. that is driven off the door locks. the OE remote key has nothing to do with it. piss if off before it strands you.

Argh.... I hate it when I have to play with eletrical things on cars :S

ill have a go on my next day off next week to disconect it

  • 2 weeks later...

Any one know exactly when they started to put transponders in the keys? I got a 2003 (march I think) and I got regular keys cut and the work to open my doors and start the car. My original key looks like the one posted above with the fob and key in one, Trunk unlock car unlock and car lock.

  • 2 weeks later...
2001 HV35 didnt have it. 2003 PV35 and CPV35 did have it.

Hi Chris - does that mean my 2001 HV35 300GT doesn't have a transponder key and I can just get a Nissan key that fits cut without worrying about the PIN Code (which I can't get anyway as the serial number isn't on the BCM)?

Thanks

Mark

this SHOULD be the case. take a snap of your key barrel with the trim ring removed OR copy the key you have onto a $5 blank with your original key and try to start the car with it. make sure the original is elsewhere when you start the car. if it starts then no issue. if not the NATS unit is there. (I'm fairly sure the former is the case.)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...