Jump to content
SAU Community

Recommended Posts

I'd be devastated if that was my car (way too much blood, sweat and tears in in...some of them mine), but the truth is it is cheap and easy to reshell these cars. Other than the shell pretty much everything Mark is running this year rolled down a hill 7 times.

Changeover cost for a new shell is less than $10k which is a drop in the ocean compared to some of these builds. I know of a full, uncomplied 33 GTR with running motor going for 12k...once you sell the motor it doesn't cost much.

Yeah it was a hard decision for us, but after alot of navel gazing we decided to reshell into an R32 because they are a bit lighter, smaller etc. The quote to fix our orange one was about $5.5k in labour plus parts and paint, so we figured we would be out of it for about $12k in total. Considering the cage ($10k cromoly job) and all running gear was fine, and its got full compliance etc, it was a tough decision..

By the time we found a good R32 shell and had it caged it owes us about the same, so still not sure if we did the right thing? We were despeartely trying to have it ready for Targa this year for my wife to run (Melinda Both, ran a pink WRX last year, 7th in early modern) , but didn't quite make it and pulled the pin a few weeks ago. She was pretty devastated and hoping to do even better this year, but after seeing the weather maybe not such a bad choice?

Anyway, the build continues and will be at Targa High Country for sure..

A couple of pics of the R32, hope I'm not getting too off topic here?

Paul

post-42431-1272713556_thumb.jpg

post-42431-1272713582_thumb.jpg

post-42431-1272713607_thumb.jpg

post-42431-1272713625_thumb.jpg

post-42431-1272713642_thumb.jpg

snowies car will fix, tis a mear flesh wound. He's lucky, the rail didn't get touched, and sill panels are cheap.

Ayres car probably won't fix from what i've been told.

sitting at the end of the straugn stage, roads are wet

Beable out with a $0.10 fuse! No ABS, 4WD or Diff from the time when the car started in the morning. Couldn't hunt it down until a service, however as he couldn't get in front of the sweep car they will have received 20 minute penalties on two stages.

they will miss out on the 12 years in a row trophy which they were aiming for.

Stoopid fuses!!!!

Congrats to Snowball!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...