Jump to content
SAU Community

Recommended Posts

I'd be devastated if that was my car (way too much blood, sweat and tears in in...some of them mine), but the truth is it is cheap and easy to reshell these cars. Other than the shell pretty much everything Mark is running this year rolled down a hill 7 times.

Changeover cost for a new shell is less than $10k which is a drop in the ocean compared to some of these builds. I know of a full, uncomplied 33 GTR with running motor going for 12k...once you sell the motor it doesn't cost much.

Yeah it was a hard decision for us, but after alot of navel gazing we decided to reshell into an R32 because they are a bit lighter, smaller etc. The quote to fix our orange one was about $5.5k in labour plus parts and paint, so we figured we would be out of it for about $12k in total. Considering the cage ($10k cromoly job) and all running gear was fine, and its got full compliance etc, it was a tough decision..

By the time we found a good R32 shell and had it caged it owes us about the same, so still not sure if we did the right thing? We were despeartely trying to have it ready for Targa this year for my wife to run (Melinda Both, ran a pink WRX last year, 7th in early modern) , but didn't quite make it and pulled the pin a few weeks ago. She was pretty devastated and hoping to do even better this year, but after seeing the weather maybe not such a bad choice?

Anyway, the build continues and will be at Targa High Country for sure..

A couple of pics of the R32, hope I'm not getting too off topic here?

Paul

post-42431-1272713556_thumb.jpg

post-42431-1272713582_thumb.jpg

post-42431-1272713607_thumb.jpg

post-42431-1272713625_thumb.jpg

post-42431-1272713642_thumb.jpg

snowies car will fix, tis a mear flesh wound. He's lucky, the rail didn't get touched, and sill panels are cheap.

Ayres car probably won't fix from what i've been told.

sitting at the end of the straugn stage, roads are wet

Beable out with a $0.10 fuse! No ABS, 4WD or Diff from the time when the car started in the morning. Couldn't hunt it down until a service, however as he couldn't get in front of the sweep car they will have received 20 minute penalties on two stages.

they will miss out on the 12 years in a row trophy which they were aiming for.

Stoopid fuses!!!!

Congrats to Snowball!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...