Jump to content
SAU Community

Recommended Posts

^^^^ That would be great Mark. After having just spoken to racing beat in the US about building a motor for me I am not so sure I want to sell all my organs plus any furure unborn children to have one of their engines. I am sure they are top notch, but circa 20-25k for a rotor engine build (complete long motor with turbo etc) is a bit beyond my budget.

But at the same time, happy to spend decent money to get something I hope will be reliable. Tassie is just too far to go for me to have a mechanical early on.

While RB did have a bit of a tech edge in the past with screw in ports, cooling mods to housings and so forth - even if they did use their alloy plates, ianettis they usually recommend, 2 piece eccentrics and so forth, that's well OTT.

consider going japanese? they know how to make a good rotor motor. had my FD RZ's motor built in japan at a shop called pre-stage. was bloody quick (in build time) and performed very well. Cost was reasonable too.

There's no secret sauce in any country - although some of the locals practicing the art here probably would have been more suited to wild west blacksmith occupations. Your ex-RZ went ker-blammo very shortly after the sale.

I am suffering the same thing..

i am really trying to get excited about building an early rotor to run in classic but am finding it hard to get really excited about it. Probabaly should have just kept the evo :(

One of the long time classic rotor guys did the switch this year, damaging the now 30k + Rx3 probably the turning point. There will be someone else doing the switch too next year.:whistling: With the price of rotor engine parts going through the roof, you can basically get 4 cylinder rods and forged pistons with change for two new rotor housings.

If you want to persist..... it's no Rx7 though.....

http://my105.com/lis...ls.aspx?id=3467

Hearing ya Ben. Advice I was given very early on was don't head to Targa with anything you can't afford or risk throwing in the bush.

Funny thing, guy I mentioned some pages ago with the GTR, ended up having to make lease payments on two cars after writing one of them off at TT.....when these were worth a bit of coin too.

^^^^ There are just so many ways to crash at Targa and sooo many variables. Even with the best intentions, some rain and a fluid spill or something else unexpected could easily have you off the road.... and then there is always the red mist to contend with if you get passed or are getting caught.... :)

bummer 2pee. didn't know that! :(

the RX4 on my105 looks pretty good value. especially with 2 engines and another in bits!

but yeah rotors can be a whole lot of pain. but when going well they are great.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...