Jump to content
SAU Community

Recommended Posts

Hey all, my r33 gtst has hot air coming out at the feet constently thru the air vent. I also have a ticking sound that goes for about 5 seconds then stops from somewhere inside or near the aircon/heater in the dash when i change the positions on the climate control. My a/c dont work cos the belt broke a while ago so i cant use that to even it out, and i think it may need a new comp. It comes out pretty warm to, i can put up with it in the mornings a 5am going to work but not on the way home, i must have the windows down to let cool air in. Has anyone had this problem or know how to fix it. The ticking sound sounds like its plastic like the old days when you would put the plastic on ya spokes of ya rim to make the sound oon ya bike. Ive been told it could be solinoid but its not that type of ticking.

Please help me someone or give me advice anything will do at the moment

Link to comment
https://www.sau.com.au/forums/topic/233987-r33-hot-air-coming-out/
Share on other sites

the ticking noise is the adjustment cog in the aircon,when you change the vent settings it moves to change the flaps and what happends is some of the teeth get striped off the wheel over time and then it just skips around in the same spot until it realises its not getting anywhere then stopes.

have ether of you had your dash out latly? there is a tube that goes to a small vent in the dash that has a small sensor it it,it uses this to work out how hot or cold it is in the cabin and then regulates the temp.if this is not connected it just defaults to max settings so you will only ether get full hot or full cold no matter how much you muck around with the temperature settings.

Jack

the hot air comes out from the feet always. press the button on your dash that looks like an arrow and your hot air will stop coming in... as for the clicking the cog inside the dash that adjusts it all has worn out and slips making a clicking noise.

Yeah ive had the dash out before but didnt notice it till a bit after i had done it, i might rip it out and have a look if the sensor is connected properly. The teeth slipping sounds about it, bugger it, how do i fix that, where is the best place to take the car to get that fixed up even, any1 know?

I get the air at my feet all the time too in my R33, It's always what ever temp I had it set on when the Climate control was on, so I was was running it on 18 with AC it would come out cold when I turn the climate control off, if I had it on heat 32, it would be hot when I turn it off.

I get the clicking noise to when I turn on the ignition and when I change the blower positions on the Climate control, fcking annoying lol

Take it to an auto electrician to have a look,

From what i understand of the stripped cog scenario, it is possible to just replace that part but the cost is up there, whereas replacing the whole thing is up there too either way the whole dash has to come out just to get to it.

mine hasnt f**ked up yet... knock on wood. the part itsself costs nothing its the labour to get to it and replace it. if youve removed the dash before its something you can do. as i said with the hot air coming from your feet thats normal. just set it to recirculate air and it will shut the vents.

Yeah ive had the dash out but damn wasnt it a pain in the arse, i ended up cracking the bloody thing an i look at it every time i jump in for a drive, its a small crack but i know its there! It must be a skyline thing, i may have a go at giving it a fix myself before summer comes round and also gotta get the a/c fixed by then. Why would they be made for hot air to constantly come out, it seems bloody strange to me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...