Jump to content
SAU Community

Recommended Posts

i was driving in stage 1.. and i stopped down to 2k's there was no car, no stop sign, no give way sign, n he sed turn right. i accelerated and turned right and then a ferrari comes driving past and he sed it was too close. pull over n i failed.

the guy was a f**king flamin mongrel too.

fkn scumbag cost me $200

($150 for my driving instructors car)

f**k VicRoad faggots =\

Link to comment
https://www.sau.com.au/forums/topic/238178-failed-ps-driving-test/
Share on other sites

Not to worry...

Should be OK next time - but hey, you've been told that already by how many?

Went thru a STOP sign on my 1st go.

Besides, I hear that...

there's a f**king flamin mongrel driving inspector around Vic somewhere & his Ferrari is being driven by his g/f

(This is 11-12 odd years ago now so I am not sure if you can still do it.)

My instructor came along for the ride on my P's test and sat in the back seat. He was well known by most of the examiners in the area. It just so happened he knew the examiner I got and they proceeded to spend the whole test gas-bagging to each other. I don't think the examiner gave a shit if I did the right thing or not. Try that! Works everytime.

i remember my test, i passed first time, it was a breaze, i guess im just an ace driver. :D

+1

L's = passed first go

red P's= ^

greens= ^

Full = ^

my reds was piss easy, 15 mins max and did the reverse park, parallel and 3 point.

The $200 must've been a bit of a sting, but you'll know what to expect for next time. Good luck! :down:

The way i see it is , Ok you have to get your red p's well...lets just get into the car and drive like an 80 year old retired baker.Once you get it what can they do , you can drive how you want to.In short form just drive like that and you will be a sure pass.

We never had anything like that.

Drove to town picked up the local copper, went for a drive. He asked how far I’d stop from a rail crossing. I said 500m. Why so far? To be on the safe side I said. Did a hill start. He said you didn’t use the handbrake. I said didn’t need to. He got out; put a bit of chalk behind the wheel. Now do it and if you crush the chalk you fail. Didn’t crush the chalk.

OK now what about my tractor licence? Where’s the tractor. On the farm, wanna go see? No she’s right.

How about my semi licence. Where’s the semi? Just stop that one (one of Dad’s).

Got in and went for a drive. These things are big he says, never been in one before. Can you reverse up that street? No worries, back it up, tear the bitumen to bits turning the tri-axle.

Shit, didn’t know it would do that, let’s go back to the station.

All good he says, just remember you can’t drive any better today because you’ve now got a licence than you could yesterday.

True.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...