Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Caltex Moorebank (Newbridge Rd) Sydney

Last night

Pump is up n running :P

Asked the Attendant if its an 85% blend or 70%

he reckons its 85% since the weather is getting warmer, and E70 is only sold in Winter when its real cold.

anyway usually when i run the stuff from United its always E85, it smells like ethanol and cold start usually stutters for a few seconds before it idles smoothly

this caltex stuff that i filled up with last night starts up 1st go perfectly so im inclined to believe that it isnt exactly E85, but closer to E70 than anything just judging from the cold start difference, and also it smells more like Unleaded than the United stuff.

Who knows

but runs the same, doesnt seem like its running richer, nor does it Knock AFAIK

post-24400-1287542963_thumb.jpg

Edited by aym23q

cool. I live just 2 mins drive from the united at rozelle but more servos around the place is a good thing. have 1,000cc injectors in the new GTR so am very seriously considering trying it out. :D

I should go past Kambah and check it out there....

But how bloody much would a full tune set me back in dyno time! fark.

It shouldn't take more than two hours to get tuned properly. Im lucky, I have a local dyno I can get on for $50 an hour now, BYO tuner. :worship:

How much were you quoted and hour?

So over the space of a few days i read this whole thread a while ago. and remember a topic on oils to use with e85.

what oils do you guys use with the e85?

Sougi 6000, discontinued unfortunately.

I used to use 300v without any issues but I would suggest you use the stock water thermostat if its a daily, as the oil needs to reach 80 degrees, to boil all the ethanol dumped into the sump at startup. (Otherwise the oil will go all milky, mine did with the low temp thermostat)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...