Jump to content
SAU Community

Recommended Posts

yeh basically as the title says i have been chasing a manual rwd stagea for a while now but to no prevail.

but seeing tho the AWD can be made into RWD quite easilly i then decided RWD wasnt a nesessaty.

then i decided im going to do sum sort of engine conversion eventually into my stagea so changing from auto to manual at the time wont cost a great deal. compared to the price diff between auto and manual stageas atm.

so i just decided any old awd auto/manual stagea will do me fine.

but cnt decide between series 1 and 2.... was the major differences apart from the lights in the grill?

yeh basically as the title says i have been chasing a manual rwd stagea for a while now but to no prevail.

but seeing tho the AWD can be made into RWD quite easilly i then decided RWD wasnt a nesessaty.

then i decided im going to do sum sort of engine conversion eventually into my stagea so changing from auto to manual at the time wont cost a great deal. compared to the price diff between auto and manual stageas atm.

so i just decided any old awd auto/manual stagea will do me fine.

but cnt decide between series 1 and 2.... was the major differences apart from the lights in the grill?

There is just such a thread on the next page (scroll down to the bottom and click on next page). BTW it is not easy to convert AWD into RWD ...if you're going to repower it just get a n/a car which are mostly RWD.

The RWD and AWD stagea's are quite different structually, and while you CAN run an AWD stagea in RWD mode, there is no real advantage because you are still carrying around all the extra weight of the attessa system. You COULD get your hands on a NA version, but if you are in Australia you will never be able to get it complied as they don't get covered under our SEVS ruling.

i'd get a s1 because they are cheaper and look alot better :P s2 fronts are shocking, definately a turn off in my book anyway.

*gets ready for flaming* :teehee:

if your changing from auto to manual u can just use a rb25 gtst box and it will get rid of the tf case, and an engine conversion will say goodbye to the front diff and sump arrangment. Then all u need is to pull the cv joints out of the front axles and just leave the part that bolts into the hub to hold the wheel bearing in and its done. Oh and remove the atessa pumps above the rear diff if u want.

i'd probably just get the rwd version if u had the choice between the two, but converting a 4wd to 2wd isnt a big drama at all.

:):P:spank::rant:

hehehe nice!

i do like the ser1 front, but its gotta be ser2 rs4s FTW!!!

if ur gonna go manual rwd then i dont think its worth getting a 4wd auto. i think u can get rwd turbo stags. it would save alot of work. but i guess if its cheaper and u have the skills then go for it. just dont forget to post up all ur wicked skid videos. :D

Edited by Raysboostin
its gotta be ser2 rs4s FTW!!!

:P

I think the rwd manual thing has been covered before, and from what my rather damaged

memory can recall, rwd stagea's werent available in manual??? im sure someone will correct

me if im wrong!

so there are NA stageas out there? but they cant be complied in aus? so theres no point in me owning one then ay cause i live in QLD...

well my eventual goals are to put a twin charged ls1 into my stagea and RWD it, so yeh i wuld prefer a stock RWD turbo or non turbo dnt phase me, and auto/manual isnt to much of a problem. rwd > awd is my major concern atm and yeh trying to find a rwd aint easy.

well, in that case you wil DEFINITELY want a RWD stagea complied in australia (the RWD stageas have a completely different shock tower arrangement and a little more room in the engine bay - this is what you will need for a wide angle LS1)

Stageas were offered all the way down to a RWD only powered by a NA RB20E

*shudders*

although why you would want one that spec is a little beyond me....

I'd say the single biggest difference between s1 & s2 is a HUGE 60NM MORE TORQUE in the s2 and at 1000RPM LESS!!

Basically its going to get up and go a lot easier and feel a lot more effortless. The extra ~20kw is just icing on the cake.

In comparison to both, the M35 is only ~30kg heavier and has ~70NM more torque again than the s2, and at the same revs as where the s2 makes its peak torque. So as you can imagine the M35 feels a lot more nimble than the s2.

Torque makes a big difference, particularly in such a heavy car. It also is one of the reasons for the better fuel economy. :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...