Jump to content
SAU Community

Recommended Posts

yeh basically as the title says i have been chasing a manual rwd stagea for a while now but to no prevail.

but seeing tho the AWD can be made into RWD quite easilly i then decided RWD wasnt a nesessaty.

then i decided im going to do sum sort of engine conversion eventually into my stagea so changing from auto to manual at the time wont cost a great deal. compared to the price diff between auto and manual stageas atm.

so i just decided any old awd auto/manual stagea will do me fine.

but cnt decide between series 1 and 2.... was the major differences apart from the lights in the grill?

yeh basically as the title says i have been chasing a manual rwd stagea for a while now but to no prevail.

but seeing tho the AWD can be made into RWD quite easilly i then decided RWD wasnt a nesessaty.

then i decided im going to do sum sort of engine conversion eventually into my stagea so changing from auto to manual at the time wont cost a great deal. compared to the price diff between auto and manual stageas atm.

so i just decided any old awd auto/manual stagea will do me fine.

but cnt decide between series 1 and 2.... was the major differences apart from the lights in the grill?

There is just such a thread on the next page (scroll down to the bottom and click on next page). BTW it is not easy to convert AWD into RWD ...if you're going to repower it just get a n/a car which are mostly RWD.

The RWD and AWD stagea's are quite different structually, and while you CAN run an AWD stagea in RWD mode, there is no real advantage because you are still carrying around all the extra weight of the attessa system. You COULD get your hands on a NA version, but if you are in Australia you will never be able to get it complied as they don't get covered under our SEVS ruling.

i'd get a s1 because they are cheaper and look alot better :P s2 fronts are shocking, definately a turn off in my book anyway.

*gets ready for flaming* :teehee:

if your changing from auto to manual u can just use a rb25 gtst box and it will get rid of the tf case, and an engine conversion will say goodbye to the front diff and sump arrangment. Then all u need is to pull the cv joints out of the front axles and just leave the part that bolts into the hub to hold the wheel bearing in and its done. Oh and remove the atessa pumps above the rear diff if u want.

i'd probably just get the rwd version if u had the choice between the two, but converting a 4wd to 2wd isnt a big drama at all.

:):P:spank::rant:

hehehe nice!

i do like the ser1 front, but its gotta be ser2 rs4s FTW!!!

if ur gonna go manual rwd then i dont think its worth getting a 4wd auto. i think u can get rwd turbo stags. it would save alot of work. but i guess if its cheaper and u have the skills then go for it. just dont forget to post up all ur wicked skid videos. :D

Edited by Raysboostin
its gotta be ser2 rs4s FTW!!!

:P

I think the rwd manual thing has been covered before, and from what my rather damaged

memory can recall, rwd stagea's werent available in manual??? im sure someone will correct

me if im wrong!

so there are NA stageas out there? but they cant be complied in aus? so theres no point in me owning one then ay cause i live in QLD...

well my eventual goals are to put a twin charged ls1 into my stagea and RWD it, so yeh i wuld prefer a stock RWD turbo or non turbo dnt phase me, and auto/manual isnt to much of a problem. rwd > awd is my major concern atm and yeh trying to find a rwd aint easy.

well, in that case you wil DEFINITELY want a RWD stagea complied in australia (the RWD stageas have a completely different shock tower arrangement and a little more room in the engine bay - this is what you will need for a wide angle LS1)

Stageas were offered all the way down to a RWD only powered by a NA RB20E

*shudders*

although why you would want one that spec is a little beyond me....

I'd say the single biggest difference between s1 & s2 is a HUGE 60NM MORE TORQUE in the s2 and at 1000RPM LESS!!

Basically its going to get up and go a lot easier and feel a lot more effortless. The extra ~20kw is just icing on the cake.

In comparison to both, the M35 is only ~30kg heavier and has ~70NM more torque again than the s2, and at the same revs as where the s2 makes its peak torque. So as you can imagine the M35 feels a lot more nimble than the s2.

Torque makes a big difference, particularly in such a heavy car. It also is one of the reasons for the better fuel economy. :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...