Jump to content
SAU Community

The Motorsport Is Dangerous Thread

Kel

By Kel,
in Motorsport Discussion & Builds

 Share

Recommended Posts

2rismo Grand Master

2rismo

Posted
Posted

The watch made the connection from the positive terminal of the uncovered fuse box to the throttle body. But it gets better - To get the spanner I was using onto the oil-filter fitting I was doing back up, I'd had to wiggle my arm down in the gap and jam it there. When the watch made the connection, it wasn't just a simple case of pulling my hand away. It was stuck for what seemed like ages.

Lesson well learned. No jewelery when working on the car and ALWAYS use the battery master shut-off.

More than a month later, it's still not great.

post-695-1227479122_thumb.jpg

post-695-1227479130_thumb.jpg

  • 3 months later...
Kel Veteran

Kel

Posted
  • Author
Posted
Kel! what are you doing to yourself! don't use your knee as a brake...

You should see how the car bit ended up :P

As I've said before, I should stick to somewhere safe, like the nav seat.

My worst injury from my down-the-bank adventure at Wrestpoint Targa was the bramble scratches I got climbing 12 foot back up the bank to the road!

Kel Veteran

Kel

Posted
  • Author
Posted
I think you should harden up girl.

Oh a little bruised knee hardly rates on the raceworx scale of injuries.

Neil.

picsorban Neily is the only way to claim top raceworx injury status

OzTME Rookie

OzTME

Posted
Posted

Hmm, Can't top the watch one, but if there's a wooden spoon for biggest pratt: here's my pitch.

I normally only wear ear protection when I'm doing something loud.

I was using my plasma cutter, and it wasn't that loud so I just wore an oxy mask. Of course, plasma cutters blow away the molten steel. Out of the corner of my eye, I see a bright red ball of steel go up from the cutter, bounce off something, and feel it go into my left ear. @#$@#$ me it hurt. Makes note to self: wear ear protection when plasma cutting.

Two days later, using the Mig welder. Wearing the full auto lcd facemask, but no ear protection, as I thought the facemask was enough protection. I'm welding, hear this pop, see a bright red ball of steel go up, bounce off something, and feel it go into my left ear. @#$@%# me, that hurt too. Turns out my big fat head and my wing nut-air brake ears are quite effective at collecting flying debris.

Went to the doctor. He said I had 2 balls of steel in my ear canal, about 1mm from my ear drum. Tried to wash it out with a syringe but failed, so had to go to a ear-nose-throat specialist. Turn up to the specialist, and he's got a dentist's chair, and a german bedside manner kinda like the dentist in the marathon man movie..

Puts me in this dentist chair, and uses tools I can't begin to describe to dig these bits of metal out of my head. It hurt more than anything I have ever felt in my life, including the time I used a pipe wrench to shatter my thumb into 5 pieces (a whole other sorry story :D)..

300$ and a whole lotta pain later, I now wear ear protection, even when making toast...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...