Jump to content
SAU Community

Recommended Posts

SAU VIC - Show N Shine & Christmas Party

Proudly sponsored by:

uniquecarsmo3.jpg

We would like to invite everyone to come down and have a look at the Show N Shine. Meet the committee and members, and get a feel for what the club is about.

When: Sunday, 30 November 2008

Time: 10:00am until 4.30pm

Where: Area 1, Caribbean Gardens Market, enter from Stud Road or Ferntree Gully Road, Scoresby. MAP of entry points

SAU Vic Cars will be displayed in Area 1 - See map below for directions to Area 1.

BUT only current member cars on display will be permitted to park in this area. All other cars will need to find parking elsewhere.

Cost: There is a small entry fee for Caribbean Gardens of $2.50/adult and $1.00/child.

The Market:

There are hundreds of stalls for you to do some last minute Xmas shopping.

There are rides for the kids and plenty more.

To check out what Caribbean Gardens offers, please check their website - http://www.caribbeangardens.com.au/CGindex.htm

Directions to Area 1:

Current SAU Vic members entering the Show N Shine MUST enter Area 1 via the top road marked on the map.

People coming to have a look, but not put their car on display must find parking nearby. You will not be permitted to park in Area 1.

shownshinecopyjf8.jpg

Link to comment
https://www.sau.com.au/forums/topic/245991-2008-show-n-shine-sun-30-november/
Share on other sites

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

lol i had to open up google maps and compare map to it because i got confused when the path in the map which is in carribean gardens is labelled as stud road i was like waahh? i know where Area 1 is now lol

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...