Jump to content
SAU Community

Recommended Posts

just want to know what people are using for suspension when they go through for an inspection?

20 year old std suspension is well gone, and im not paying $200 for a set that might pass or leak, so whats the deal these days? Would they allow a set of Bilsteins pass at legal height? They arnt adjustable like the normal "screw up and down" type like you normally see, just a circlip adjustment.

just want to know what people are using for suspension when they go through for an inspection?

20 year old std suspension is well gone, and im not paying $200 for a set that might pass or leak, so whats the deal these days? Would they allow a set of Bilsteins pass at legal height? They arnt adjustable like the normal "screw up and down" type like you normally see, just a circlip adjustment.

friend of mine has passed regency with that style strut many times.

I am assuming you are after a set to suit a 32??

yerp

friend of mine has passed regency with that style strut many times.

I would assume they would let these through, as the only adjustment is via a circlip, which if there is only one groove means no other adjustments.

If they are adjustable below legal height they shouldn't pass, however they might pass them if it isn't obvious that they are adjustable.

Or if the height is reasonable they might not even look.

Edited by Rolls
  • 2 weeks later...

Depends where the boost gauge is, if its in a vent or down below the dash it is fine, on the dash or a pillar you can't have it though.

Turbo timer is illegal because if you have a crash and the car get a fuel leak and it keeps running, sup massive fire. They shouldn't have given you roadworthy with it connected.

See i've never got that rule/law, as in heavy trucks they ALL come with turbo timer's standard and keep running even if you turn the maxi's off...

See i've never got that rule/law, as in heavy trucks they ALL come with turbo timer's standard and keep running even if you turn the maxi's off...

Someone explained it here years ago i think, but trucks are a different kettle of fish, being much larger motors running huge turbos that are running max pressure towing loads all the time. They need the time to help cool the turbos down, unlike cars chugging along at a regular 60km/h pulling 2.5krpms per gear change.

See i've never got that rule/law, as in heavy trucks they ALL come with turbo timer's standard and keep running even if you turn the maxi's off...

Diesel engines have mechanical fuel pumps, if the engine stalls the engine stops pumping fuel, if there is a fuel leak then the engine will almost certainly stall due to the MASSIVE pressure the lines are under, but being metal lines they almost certainly wouldn't leak.

So basically you have an accident in a truck as soon as there is a fuel leak that could cause a fire the engine basically stalls anyway, hence stopping the fuel pumping into the fire. In a petrol engine if they crash and stall the electric pump will keep pumping regardless.

Also diesel isn't as flammable as petrol.

Edited by Rolls

So i'm looking at buying 'Longz' R34 GTR from NSW, from my understanding it'll need to get an identity check which does involve some pit checks.

It has the following:

"* Apexi Power FC with Commander ($1600)

* HKS Boost Controller ( $800 )

* Z-Tune Carbon Fibre Bonnet with Carbon Fibre Aero flush pins fitted. ( $850+300 )

*Apexi Pen Turbo Timer ( $100 )

* Tomei Cam Pulleys ( $520 )

* Ganador Titanium Exhaust

* Nitto Clear Cam Cover ( $120 )

* BC Coilovers fitted 2500km ago $1300 have reciept"

What would i need to change back to stock? I'm guessing a lot of it......

This vehicle identity check, can i get this done anywhere else besides regency/lonsdale?

Edited by occxlr8ed

Any police station will do it, but if they suspect it is modded it will be sent to regency, If so the following will need to be returned to standard:

Turbo timer - removed

cam pulleys if visible removed

exhaust if above legal limit removed

coilovers almost certainly will need to be removed for both pits and regency as they will be adjustable and too low

bonnet 100% needs to be removed as it doesn't pass ADRs

Boost controller removed

Power FC removed and stock ecu installed

depends on the rim size but if they exceed the ADRs also returned to stock

my advice is wind the coilovers as high as possible, buy a set of stock rims and remove all fancy things, also put a non clear timing cover on, that should make it look stock, oh and obviously take the stupid CF bonnet off haha that will be instant ass f**king

Edited by Rolls

freaking attention that skylines get!!!

the past 2 years of driving my 350z, lowered to about 4cm of ground clearence, etc. etc. i've had ZERO problem, not one cop pull me over....

if you get a defect sticker is it the same deal? i've had my mates get theirs cleared at a cop station instead of regency however that was just for tint and the other case headlights.

Edited by occxlr8ed

freaking attention that skylines get!!!

the past 2 years of driving my 350z, lowered to about 4cm of ground clearence, etc. etc. i've had ZERO problem, not one cop pull me over....

if you get a defect sticker is it the same deal? i've had my mates get theirs cleared at a cop station instead of regency however that was just for tint and the other case headlights.

Ive never been defected driving on the roads, but I have almost been defected quite a few times, mainly due to doing stupid stuff and just getting out of it.

Minor defect is police station eg what you just mentioned, major defect (suspension, too loud, turbo etc) is regency.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...