Jump to content
SAU Community

Recommended Posts

in terms of kw at the wheels, what would be the saffest power and max power to be running at the wheels.. ie. what figure you should not be aiming to go over.... 350rwkw on an internally stock rb26 ??

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

it did eventually blow up on him.. but he was making around 500hp... i think your referring to this thread -->

http://www.skylinesaustralia.com/forums/Ma...25-t106775.html

It blew on him as he was pushing more and more nitrous into it.

I know Jason, have seen the car.

Ran a 10.8 IIRC with him backing off BEFORE the line.

Was making 370 odd RWKW, with Nitrous.

^^ its been covered so many many times now dude. You should have a search.

Reliable (5+ years) seems to be 300-330rwkw. Anymore than that and the motors are limited.

Nothing is reliable when you mention un opened rb26dett :D

wheres the timeslip?

you cant claim the title without a timeslip.

dyno printouts or sketchy, mph tells all.

when did dyno printouts come into it??

vid of the run

http://au.youtube.com/watch?v=GDsQb5DShrY

  • 8 months later...

10.675 @ 137.89mph from memory.

It did have 260 deg pon cams and cam gears set to zero (I still class it as an unopened engine). It was also with a 50hp shot of gas. Just good bolt ons (T517z's).

The car was raced with full furnature, street exhaust, street legal tyres, stereo etc....

oorrr thread just got interesting .....

so no cams, no cam gears ?

Got a copy of the time slip ?

10.6 what ??

I thort it might come down to 1/10ths.

anyone else remember this... i cant find it... NO idea what keywords to use :D

i remmeber std internal r33's running high 10's done by CREATD a few years back and low 11's on radials. and one of their white r33 gtr's did a 10.60.

Ahh the good ol days. I wanted that 10 sec slip so bad..... At that time Tassie was the last state to run a 10sec GTR pass. I got a lot of help over the phone from Peter Hall for set up and some driving tips from Kier Willson...

That engine lasted nearly 2 years... untill I un/intentionally?? blew it the day before I left to go work overseas.

10.675 @ 137.89mph from memory.

It did have 260 deg pon cams and cam gears set to zero (I still class it as an unopened engine). It was also with a 50hp shot of gas. Just good bolt ons (T517z's).

The car was raced with full furnature, street exhaust, street legal tyres, stereo etc....

I think you'll find its 440awkw.

No chance im saying who it is :banana:

well thats a timebomb waiting to happen.

i had a stock bottom end with gtrs setup - 9mths later BANG (362awkw)!

another stock bottom end with gtss setup - 6mths later BANG (322awkw)!

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...