Jump to content
SAU Community

Got Over 400kw Atw?

T04GTR

By T04GTR,
in Engines & Forced Induction

 Share

Recommended Posts

Beer Baron Grand Master

Beer Baron

Posted
Posted

looks like 2 rb's to make a v12 (similar to 2 v8s which makes the bugatti w16) LOL

those turbo's will keep the rear tubs warm, no need for tyre warmers

lol! I'm not sure what you're on but they need to raise or lower the dosage! NOW!!! :domokun:

  • Replies 3.3k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

colinhunt
colinhunt

Let's not turn yet another thread into a discussion about your car, please.

Lithium
Lithium
SiR_RB
SiR_RB

Posted Images

WHITER33GTS-T Veteran

WHITER33GTS-T

Posted
Posted (edited)

There are folks in the US who have on Supras and Hondas that I have seen with gains over normal GT4202Rs. I know someone who is in the process of putting together a twin GTX4508R setup, though thats just silly.

Would that be on a nissan V8..? VK56 maybe in a rail...? :worship:

The rest of the page just loaded. lol

Rob is mad. :cheers:

Edited by WHITER33GTS-T
Brezza Proficient

Brezza

Posted
Posted

Could any of you blokes let me know at what level the std RB26 conrods tend to break.

I'm pushing high 300's with my GTR and the tuner said that on e85 the torque produced could be too much for the std rods to handle.

the motor has forged pistons etc but i left the rods std because when i had it built i didnt think i was going to attempt to push for 400kw

Rolls Grand Master

Rolls

Posted
Posted (edited)

I was of the opinion that rods and rod bolts broke due to rpm, and pistons generally break from higher torque (heat) and detonation. Obviously the rods will let go eventually, due to power but I thought that level would be quite high?

I could be wrong though, someone feel free to correct me.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...