Jump to content
SAU Community

Recommended Posts

+1 Dave. So sick of the "how do I raise my boost for free" shit threads and people wanting mega power on a shoestring budget lately!

How's your setup coming along for power cruise? Give us some good news!!!

Matching turbos and supporting mods to achive a practial/streetable Car has nothing to do with "raising boost for free" or even a budget for that matter, Our cars are money pits No matter which route you choose, Just aslong as you have fun with it

Practical street car talk is over here;

http://www.skylinesaustralia.com/forums/topic/236467-definitive-guide-to-building-300-330awkw-gt-r/

Enjoy! :) (Not being rude, but anyone in here with 400kw doesn't really give a shit about practicality)

Getting some stuff done at Speedfab, should be back at JEM by the end of the week to get all bolted up.

Cutting it fine as usual. :rolleyes:

Got to admit, you're consistent haha

Havnt heard of speed fab before-tell us a bit about them?

His name is Rob, PJ put me onto him. Did all of his metal fab stuff.

He made a manifold for a customer at JEM. Top notch stuff, so he made my new one, shroud for thermo, a bit of pipe work.

So yeh, fingers crossed it all comes together in the next week or 2. It will be a car to keep your ears open for at Powercruise :)

Practical street car talk is over here;

http://www.skylinesaustralia.com/forums/topic/236467-definitive-guide-to-building-300-330awkw-gt-r/

Enjoy! :) (Not being rude, but anyone in here with 400kw doesn't really give a shit about practicality)

I would just like to have some more time behind the wheel in between breakages. :cheers:

finally cracked the 400 mark

r33 gtr 1995

rb26

engine

honed/bored 0.20# , acid dipped all usual machining done ect

shot peened n1 rods with enlarged big end bearings , crank balanced re nitrided and oversized 0.60 acl race bearings

arias 0.20 over pistons , acl piston rings

tomei oil restrictor

tomei sump bafffle/trap doors

N1 water pump ,

s oil pump

genuine nissan gasket set throughout

cossworth drag series 1.5mm metal head gasket

head reconditioned with porting on exhaust side , hks 264 cams greddy adjustable cam gears

arp head stud kit

driveline

Very rare Autogallery yokohama 1-5 H/D set with double cone syncro's , redline shockproof oil

Os giken pro series twin plate push type clutch

Vspec rear active lsd diff

Turbo/exhaust/intake

Trust greddy t517z turbos with 10cm housings

standard manifolds match ported

hks non turbulent dump pipes

custom twin 3inch y pipes with 100cfm race cats y pipes individualy run to centre of car and then merge into 3.5inch exhaust with highflow muffler and 5 inch tip

apexi hard pipe intake kit with twin z32 afm

electronics/ignition/fuel

apexi power fc , with hand controller

blitz 4 stage electronic boost controller

bosch single 044 mounted intank

injector dynamics 1000cc injectors with convertors t fit 10.5mm standard rail

turbosmart adjustable fuel pressure reg

splitfire coilpacks

hks twin spark DLI amplifier

low compression engine tested 128- 132 across all 6 due to 1.5mm h/g , current power 405kw@wheels on mainline dyno at 23psi fuel pump is probably near its limits but this is plenty for me!!

post-46933-0-16803400-1328176571_thumb.jpg

Good result man! No spark issues with the Twin Spark?

Prob a bit more left in it with a little more boost!

by installing your hks twin spark and splitfires and adding 3psi gained 55 kw atw f*kkn redicolous gains lol , must have been missfiring somethiung fierce before!!

finally cracked the 400 mark

r33 gtr 1995

rb26

engine

honed/bored 0.20# , acid dipped all usual machining done ect

shot peened n1 rods with enlarged big end bearings , crank balanced re nitrided and oversized 0.60 acl race bearings

arias 0.20 over pistons , acl piston rings

tomei oil restrictor

tomei sump bafffle/trap doors

N1 water pump ,

s oil pump

genuine nissan gasket set throughout

cossworth drag series 1.5mm metal head gasket

head reconditioned with porting on exhaust side , hks 264 cams greddy adjustable cam gears

arp head stud kit

driveline

Very rare Autogallery yokohama 1-5 H/D set with double cone syncro's , redline shockproof oil

Os giken pro series twin plate push type clutch

Vspec rear active lsd diff

Turbo/exhaust/intake

Trust greddy t517z turbos with 10cm housings

standard manifolds match ported

hks non turbulent dump pipes

custom twin 3inch y pipes with 100cfm race cats y pipes individualy run to centre of car and then merge into 3.5inch exhaust with highflow muffler and 5 inch tip

apexi hard pipe intake kit with twin z32 afm

electronics/ignition/fuel

apexi power fc , with hand controller

blitz 4 stage electronic boost controller

bosch single 044 mounted intank

injector dynamics 1000cc injectors with convertors t fit 10.5mm standard rail

turbosmart adjustable fuel pressure reg

splitfire coilpacks

hks twin spark DLI amplifier

low compression engine tested 128- 132 across all 6 due to 1.5mm h/g , current power 405kw@wheels on mainline dyno at 23psi fuel pump is probably near its limits but this is plenty for me!!

How do you find the gearbox? Have you driven the Os Giken one to compare it too?

That should be in the title. A disclaimer like "if you're after response, do not click this thread"

LOL ye not like people are running 540ci motors.

Some results in here are pretty damn decent for the power none the less.

Its all about the number nismoid. This thread isnt about response haha

It should be. Why would you not want your cake and eat it too?

Noel makes 24psi by about 3500rpm from memory and he doesn't even have the VCT back on it yet. Correct turbo selection and head setup and you can make 550-600hp and still have good response

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...