Jump to content
SAU Community

Recommended Posts

Bang for buck was why I went with the Z, and for my application its not under 4200 anyway so responce is mute then, it is a little sluggish getting going if you dont give it some revs from idle to 4000 but Ive found that on trackdays it is always on the boil anyway, how is your beastie going mate, got it all bolted up yet ?

Looking forward to seeing it go out in anger.

Nice, I might see it when my boat goes in next week.

And the boat is not track only, it comes out when its raining because my motorbike is made of sugar, I also plod around the Grove (read: bottleshop) in it too, it was fun at the cruise too..

The 3ltr is the bomb though, even with the delay in spool time the extra torque pulls it out of the hole.

-10s are cheap and for the 3ltr the ultimate low combination for the street. Ppl that have built rb26/30s know this

Sorry MarkO I've got that engine, and have had those turbos, and there is no way I'd be calling them "ultimate".

-10s are cheap and for the 3ltr the ultimate low combination for the street. Ppl that have built rb26/30s know this :)

no they aren't the -5 is and we both know the same people who will support my argument

I can't comment on the -5s with 3ltr...I keep thinking they're a bit small as I've yet to see results of this combo. Hurry up stevo and prove me wrong.

I wonder what my combo would have made on higher boost with e85!?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...