Jump to content
SAU Community

Recommended Posts

Matt Tang was telling me his vcam RB28 would push the -5's into surge occasionally. A combination of the added displacement providing a little more exhaust flow than a 26, and vcam inducing more overlap to to gain more mid range torque earlier in the rev range. The advice I heard Racepace gave Matt was that the surge could be tuned out, but at the expense of low end torque, most likely making the vcam retard the intake earlier.

So what we can take from this is that if your engine is optimised to the limit, even -5's will push into surge.

(I'm talking surge here, not shuffle... don't confuse the two)

My -5s will surge only on a 5-8 degree morning, full load in 5th coming onto boost. Could be tuned out if i really wanted as you said, any warmer and it was fine so it wasnt a problem. It was more conditions than anything else - such a rare thing that happens maybe once/twice a year.

What is the difference between shuffle and surge as I am not aware?

Same thing, different words

In your case Ash they'd retard the ignition which would make more doey to drive when its hot, and not as fun when its cold...I'd rather have surge than shuffle.

Shuffle can be seen on a data logger when the airflow values read from your twin maf sensors wildly fluctuate. I had big problems with this at around 1800-2000 rpm with my GTRS's as they start making around 0.4kg/cm under full load at this speed. However as exhaust flow isn't enough to spin the turbo's up to wastegate opening speeds, and the engine is running in a vacuum at the throttle bodies the effect is that one turbo will spin up and stall the airflow into the other. Once this happens the exhaust pressure in the stalled turbo swings the shuffle the other way. The GTRS's suffer for this because the compressor is too big for the turbine.

This is why a HKS balance pipe exhaust manifold helps dampen the effect. Also it explains why the split/baffeled twin turbo pipe helps so much, as it allows air velocities out of each turbo to be established before mixing them back into one air stream before the intercooler.

For me, I still get shuffle if I stand on the throttle in 4th at 2000 rpm. It will shuffle (till full boost at 5000 rpm), where exhaust flow and back pressure is sufficent to overcome the shuffle effect. You can drive around this though as really you'd drop back to 2nd or third anyway if you wanted to go faster.

Surge won't effect response, in fact surge is the result of too much response (for a given engine speed). The turbo's are being over driven by exhaust gas flow for a given engine speed. The rate of airflow into the engine (from the filters to the intake valve) is below what is the optimal air speed for the given compressor speed. The effect is your turbo makes terrible sounds as the airflow stalls out and bleeds back to the intake of the turbine housing, which can lead to turbine damage.

I hope that makes some sense. Im operating on minimal speel and 2 glasses of red at the moment...

I'd argue the point of surge not hurting response, if its bad enough it can basically have the car "stall" at a given point in RPM until it pushes through.

If low enough in the RPM this can take quite a while.

When i can get mine surging, low rpm/5th/6 degree ambient - it will not go past that RPM point at all even if i hold it there for 10 seconds. I have to drop back to 4th, pass that RPM window (about 300rpm) and then it's fine.

They way I understand surge is that airflow stops because it cant go anywhere, except bleed back out the turbo inlet, so would I be rightin think that airflow stops or even reverses to an extent?

I remember my old highflow would surge like crazy at around 3000rpm in 5th when cruising down the highway, send the PFC Haywire and the motor would cough and splutter then clean up for a few seconds and repeat

could hear it surging a mile away...like a Chappel st VL lol

driving down the highway going tutuutututut constantly

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...