Jump to content
SAU Community

Recommended Posts

There is a product called 'crystalite' that now has ADR approved headlight tints. Its not a film but a micro resin that bonds to the light. It is quite expensive because you can't DIY. Needs a qualified Applicator. 5 or so colours and claims to be heaps stronger than the OME light (polycarbonate lenses) surface so scratches are avoided. Tell me what you reckon? click the link!

http://www.flickr.com/photos/12281250@N02/

PS. I am considering becoming an applicator.

Edited by R34GT-T
Link to comment
https://www.sau.com.au/forums/topic/252545-tinted-headlights/
Share on other sites

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

i have actually seen an r33 with a tinted headlights and i have to say it looks really mean and heaps better looking than the standard lights, and they look expensive i liked it, it makes the car stand out more it was at vic fawkners kfc, if this guy is here i hope he would post some photos so everyone can have a look but the car looks way better. how much do they cost?

I only have one opinion about the concept of applying a light-reducing tint to a surface designed to allow light to pass through it in order for you to see where you're going.

f**king stupid.

100 percent agree. Would have to be one of the dumbest things you could do for safe night time driving.

And i highly doubt its adr aproved

I only have one opinion about the concept of applying a light-reducing tint to a surface designed to allow light to pass through it in order for you to see where you're going.

f**king stupid.

It depends on the direction in which it reduces light.

If it only reduces light going from the outside world into the housing (like a 1 way mirror only stops light passing through in 1 direction) then I reckon it's great. I've seen cars with tinted lights and it looks tough.

If it reduces both ways, I'd be inclined to agree with you.

a one/two way mirror (heard it called both) only works because it has a thin metallic film on one side that reflects light in the bright room, making the window seem like a mirror. Therefore you can't see anything in the darker room because the reflection is brighter.

there's no such thing as a material that's "one way" with light.

I only have one opinion about the concept of applying a light-reducing tint to a surface designed to allow light to pass through it in order for you to see where you're going.

f**king stupid.

so you don't have tinted windows i take it?

i've noticed he does that... no offence dude, but you're running with the big boys here

I wouldn't tint my headlights if it stopped any light coming out... which is pretty much the definition of tinting...

so you don't have tinted windows i take it?

Unless kinks is a mad hectic street drifter, he won't really be "looking where he is going" out of his side windows. Front windshield tinting is illegal, aside from the sunvisor strip at the top.

so we should ban this?

34y48ir.jpg

Yes. It's f**king hideous.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...