Jump to content
SAU Community

Recommended Posts

  • Replies 193
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

woo you're coming!

+1 patrick, anthony, sandeep and jake in one group :P will be easier for ant and I going for the first time

thnks

It can be arranged. I'll try to remember when im doing the groupings next week.

entry forms sent by email

payment transfered

I will bring my CAMS form and payment on the day and will be Joining as a member of SAU at the renewal this Sat.

see you all there :P

EDIT: Please put me in the slower group as its my 1st DECA

Edited by 180Roman
^^Its my first deca day too!!

I recognise your username off ns.com about the firextinguishers

yay Silvia/180sx buddies

yay more silvias/180sxs, i was starting to be intimidated by that list of GTS-Ts, GTRs and a few EVOs in the mix :D

yeah i was asking about the firextingushers so i could have my car ready for this DECA :blush:

Hey ryan , Not sure if its too late or not , But if possiable would you be able to put Russel Gilder in the same grp as me

and smicko . AND also can u make smicko go first for a change :P lol

cheers Bud

yay more silvias/180sxs, i was starting to be intimidated by that list of GTS-Ts, GTRs and a few EVOs in the mix :P

I think Leon (achoo) may leave the 33 at home and bring his 180 if its ready in time

So there is 1 more..

I PM'ed Chris but can u drop Mario and I in the same group

5-6 cars separation would be good so we can both do camera work

oh I'm bringing the GoPro stick on camera as well..so if you in my group or in the battles and want some on car action give me a yell on the day.

cheers

M

entry faxed!

i dont mind which group, but can i be put with my mate Jason W. he'll be faxing his entry through shortly as well

thanks bec :D

sweet robby, you and jase are coming!, bec i've been convinced and will send off my entry tomorrow, put me with these 2 guys also if thats ok.thanks. btw its ben if you couldn't gather...

Edited by skypy12
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...