Jump to content
SAU Community

Recommended Posts

Yo i stalled my car today.. but clutch was completely in.. and normally when i stall the lights come up on dash board.. this time it didnt..

Any1 know what it is and how much to fix?

so when your car is in neutral and stalls...

on alot of cars...tbe the throttle position sensor may need cleaning.

what sort of car or maintenance on the engine?

This has happened to me a couple of times also when the clutch was fully pressed in and been coming to a stop. Me thinks its nothing to do with the clutch though, and as others have said it feels like something to do with engine. Only has happened twice in two years i've had the car so i'm not too worried about it....

Huh?

If the clutch is all the way to the floor, and it stalls, it's the clutch slave cylinder... or the master.

Happened to me in my car a few months back.

yeah i dont think its got to do with anything regarding the clutch

things like this are more likely the throttle position sensor...AAC ... blocked vaccume hoses can also produce this affect...and ECU faults can do this as well.

Mine used to do it until, I got rid of the clutch line loop back block that sits in between the clutch master and slave cylinder.

Pulled that out and bought a braided clutch line from jj that goes straight from the master to the slave and I couldn't be happier with the clutch action now.

It doesn't try to stall the engine when you come to a stop with the clutch in, in gear.

it doesnt really sound like your problem, but when i replaced my o2 sensor it fixed all my stalling problems 100% (touch wood), but mine really only stalled when i bipped the accelerator and went on the brakes.

EDIT: actualy after reading through all this, most people seem to think its to do with the clutch, most likely not, wats ur idle like when warm and cold?, wat about with the a/c on? and when u steer does ur engine struggle a bit or do the revs go up? if ur idle is low all the time u probably just need to reset and adjust it. if ur idle is fine (warm/cold start and with a/c) but the engine struggles when its under load (braking at the lights, turning the steering wheel, maybe even bipping the throttle) then its probably the aac valve, air flow meter, or even the o2 sensor. how many km's has your car done?

quick question, ur not running anything under 98RON fuel are you? this will cause ur car to run and idle like shit

Edited by xdef

when i first got my car, it had an atmo venting bov (a blow off valve that goes psssshhhhht into the air). i had this same type of stall happen to me a few times, randomly, always when coming onto the brakes with clutch in. the more sudden the action, the more likely it was to almost stall, occasionally stalling.

plumbed the bov back in. never had this issue again.

so, if you dont have a blow off valve, forget everything i said. if you do, i would consider this a high priority on your check list.

edit: i just read your original post again, and realised you may have just been idleing at the lights, not coming onto the brakes at all. if so, its prob not the bov.

dont know why i imagined braking lol.

Edited by Munkyb0y

luckieee

do you often use the clutch to change the gears in your auto?? :P

if so i think that is where your problem is...

just rip your clutch pedal out that should solve the problem

Corey,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...