Jump to content
SAU Community

Car Stalled But Clutch Was Completely In..

Luckieee
 Share

Recommended Posts

eeiko321 Experienced

eeiko321

Posted
Posted
Yo i stalled my car today.. but clutch was completely in.. and normally when i stall the lights come up on dash board.. this time it didnt..

Any1 know what it is and how much to fix?

so when your car is in neutral and stalls...

on alot of cars...tbe the throttle position sensor may need cleaning.

what sort of car or maintenance on the engine?

SLEEPR85 Proficient

SLEEPR85

Posted
Posted

This has happened to me a couple of times also when the clutch was fully pressed in and been coming to a stop. Me thinks its nothing to do with the clutch though, and as others have said it feels like something to do with engine. Only has happened twice in two years i've had the car so i'm not too worried about it....

eeiko321 Experienced

eeiko321

Posted
Posted
Huh?

If the clutch is all the way to the floor, and it stalls, it's the clutch slave cylinder... or the master.

Happened to me in my car a few months back.

yeah i dont think its got to do with anything regarding the clutch

things like this are more likely the throttle position sensor...AAC ... blocked vaccume hoses can also produce this affect...and ECU faults can do this as well.

GTRsean Grand Master

GTRsean

Posted
Posted

Mine used to do it until, I got rid of the clutch line loop back block that sits in between the clutch master and slave cylinder.

Pulled that out and bought a braided clutch line from jj that goes straight from the master to the slave and I couldn't be happier with the clutch action now.

It doesn't try to stall the engine when you come to a stop with the clutch in, in gear.

3LGODZILA Proficient

3LGODZILA

Posted
Posted (edited)

it doesnt really sound like your problem, but when i replaced my o2 sensor it fixed all my stalling problems 100% (touch wood), but mine really only stalled when i bipped the accelerator and went on the brakes.

EDIT: actualy after reading through all this, most people seem to think its to do with the clutch, most likely not, wats ur idle like when warm and cold?, wat about with the a/c on? and when u steer does ur engine struggle a bit or do the revs go up? if ur idle is low all the time u probably just need to reset and adjust it. if ur idle is fine (warm/cold start and with a/c) but the engine struggles when its under load (braking at the lights, turning the steering wheel, maybe even bipping the throttle) then its probably the aac valve, air flow meter, or even the o2 sensor. how many km's has your car done?

quick question, ur not running anything under 98RON fuel are you? this will cause ur car to run and idle like shit

Edited by xdef
Munkyb0y Grand Master

Munkyb0y

Posted
Posted (edited)

when i first got my car, it had an atmo venting bov (a blow off valve that goes psssshhhhht into the air). i had this same type of stall happen to me a few times, randomly, always when coming onto the brakes with clutch in. the more sudden the action, the more likely it was to almost stall, occasionally stalling.

plumbed the bov back in. never had this issue again.

so, if you dont have a blow off valve, forget everything i said. if you do, i would consider this a high priority on your check list.

edit: i just read your original post again, and realised you may have just been idleing at the lights, not coming onto the brakes at all. if so, its prob not the bov.

dont know why i imagined braking lol.

Edited by Munkyb0y
sIIgtst Rising Star

sIIgtst

Posted
Posted

luckieee

do you often use the clutch to change the gears in your auto?? :P

if so i think that is where your problem is...

just rip your clutch pedal out that should solve the problem

Corey,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...